A Computational Study into the Effect of Design Parameters on Ignition Timing and Emission Characteristics of HCCI Engine in Internal Combustion Engines Fuelled with Isooctane
 W. Ying, H. Li, Z. Jie, and Z. Longbao. “Study of HCCI-DI combustion and emissions in a DME engine,” Fuel, vol. 88, no 11, pp. 2255-2261, 2009.
 M. Fathi, R. K. Saray and M. D. Checkel. “The influence of Exhaust Gas Recirculation (EGR) on combustion and emissions of n-heptane/natural gas fueled Homogeneous Charge Compression Ignition (HCCI) engines,” Applied Energy, vol. 88, no 12, pp. 4719-4724, 2011.
 J. Jang, Y. Lee, C. Cho, Y. Woo and C. Bae. “Improvement of DME HCCI engine combustion by direct injection and EGR,” Fuel, vol. 113, pp. 617-624, 2013.
 F. Foucher, P. Higelin, C. Mounaїm-Rousselle and P. Dagaut. “Influence of Ozone on the Combustion of n-Heptane in a HCCI Engine,” Proceedings of the Combustion Institute, vol. 34, no 2, pp. 3005-3012, 2013.
 H. S. Yücesu, T. Topgül, C. Cinar, and M. Okur. “Effect of ethanol–gasoline blends on engine performance and exhaust emissions in different compression ratios,” Applied Thermal Engineering, vol. 26, no 17, pp. 2272-2278, 2006.
 R. C. Costa, and J. R. Sodré. “Compression ratio effects on an ethanol/gasoline fuelled engine performance,” Applied Thermal Engineering, vol. 31, no 2, pp. 278-283, 2011.
 P. M. Najt and D. E. Foster, “Compression-ignited homogeneous charge combustion,” SAE Technical paper, 1983.
 N. Iida and T. Igarashi, “Auto-ignition and combustion of n-butane and DME/air mixtures in a homogeneous charge compression ignition engine,” SAE Technical Paper, 2000.
 C. Sayin and M. Gumus. “Impact of compression ratio and injection parameters on the performance and emissions of a DI diesel engine fueled with biodiesel-blended diesel fuel,” Applied thermal engineering, vol. 31, no 16, pp. 3182-3188, 2011.
 S. S. Karhale, R. G. Nadre, D. K. Das and S. K. Dash. “Studies on comparative performance of a compression ignition engine with different blends of biodiesel and diesel under varying operating conditions,” Karnataka Journal of Agricultural Sciences, vol. 21, no 2, 2010.
 S. Puhan, R. Jegan, K. Balasubbramanian and G. Nagarajan. “Effect of injection pressure on performance, emission and combustion characteristics of high linolenic linseed oil methyl ester in a DI diesel engine,” Renewable Energy, vol. 34, no 5, pp. 1227-1233, 2009.
 J. B. Heywood. “Internal combustion engine fundamentals,” New York: McGraw-Hill, 1988.
 G. Woschni. “A universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine,” SAE Technical paper, 1967.
 M. Yanbin. “HCCI Heat Release Rate and Combustion Efficiency: A Couple KIVA Multi-Zone Modeling Study,” ProQuest, 2008.
 E. A. Ajav, B. Singh and T. K. Bhattacharya. “Performance of a stationary diesel engine using vapourized ethanol as supplementary fuel,” Biomass and Bioenergy, vol. 15, no 6, pp. 493-502, 1998.
 T. D'Andrea, P. F. Henshaw and D. K. Ting. “The addition of hydrogen to a gasoline-fuelled SI engine,” International Journal of Hydrogen Energy, vol. 29, no 14, pp. 1541-1552, 2004.
 B. Challen and R. Baranescu, “Diesel engine reference book,” McFarland, 1999.