Open Science Research Excellence

Open Science Index

Commenced in January 2007 Frequency: Monthly Edition: International Publications Count: 29609


Select areas to restrict search in scientific publication database:
9997092
Modeling and Simulation of Delaminations in FML Using Step Pulsed Active Thermography
Abstract:
The study focuses to investigate the thermal response of delaminations and develop mathematical models using numerical results to obtain the optimum heat requirement and time to identify delaminations in GLARE type of Fibre Metal Laminates (FML) in both reflection mode and through-transmission (TT) mode of step pulsed active thermography (SPAT) method in the type of nondestructive testing and evaluation (NDTE) technique. The influence of applied heat flux and time on various sizes and depth of delaminations in FML is analyzed to investigate the thermal response through numerical simulations. A finite element method (FEM) is applied to simulate SPAT through ANSYS software based on 3D transient heat transfer principle with the assumption of reflection mode and TT mode of observation individually. The results conclude that the numerical approach based on SPAT in reflection mode is more suitable for analysing smaller size of near-surface delaminations located at the thermal stimulator side and TT mode is more suitable for analysing smaller size of deeper delaminations located far from thermal stimulator side or near thermal detector/Infrared camera side. The mathematical models provide the optimum q and T at the required MRTD to identify unidentified delamination 7 with 25015.0022W/m2 at 2.531sec and delamination 8 with 16663.3356 W/m2 at 1.37857sec in reflection mode. In TT mode, the delamination 1 with 34954W/m2 at 13.0399sec, delamination 2 with 20002.67W/m2 at 1.998sec and delamination 7 with 20010.87 W/m2 at 0.6171sec could be identified.
Digital Object Identifier (DOI):

References:

[1] Ad Vlot and Jan Willem Gunnink, "Fibre Metal Laminates”: An Introduction. Kluwer Academic Publishers. Springer Netherlands, 2001.
[2] ANSYS, ANSYS Heat Transfer Manual for Release 10, 2005.
[3] Avdelidis N. P and Almond D.P, "Transient thermography as a through skin imaging technique for aircraft assembly Modelling and experimental results”, Journal of Infrared Phys. Technol., Vol. 45. No. 2, pp. 103-114, 2004.
[4] Avdelidis N.P, Almond D.P, Dobbinson A, Hawtin B.C, Ibarra-Castanedo C and Maldague X, "Aircraft composites assessment by means of transient thermal NDT”, Progress in Aerospace Sciences, Vol. 40, pp 143–162, 2004.
[5] Guillen and Can, "The influence of cooling rate on the fracture properties of a thermoplastic-based FMLs”, Journal reinforced plastics and composites, Vol. 21. No. 8, pp. 749-772, 2002.
[6] Hagenbeek M, "Characterisation of Fibre Metal Laminates under Thermo- mechanical Loadings”. PhD thesis. Faculty of Aerospace Engineering, 2005, Delft University of Technology, pp 224.
[7] Ibarra-Castanedo C, Grinzato E, Marinetti S, Bison P, Genest M, Grenier M, Jean-Marc Piau, Bendada A and Maldague X, "Recent progresses in the inspection of aerospace components by infrared thermography” 17th World Conference on Nondestructive Testing, 2008, Shanghai, China, pp.25-28.
[8] Ibarra-Castanedo1 P, Avdelidis N.P, Grinzato G, Paolo G, Sergio M, Claudiu P, Abdelhakim B and Maldague X, "Delamination detection and impact damage assessment of GLARE by active thermography”, International Journal of materials and Product Technology, 2011, Vol. 41, pp. 5-16.
[9] Krishnapillai M, Jones R, Marshall I.H, Bannister M, and Rajic N, "NDTE using pulse thermography: Numerical modeling of composite subsurface defects”, J. Composite Structures, Vol. 75, pp. 241-249, 2006.
[10] Lugin S and Netzelmann U, "A defect shape reconstruction algorithm for pulsed thermography”, NDT&E International, Vol. 40, pp. 220–228, 2007.
[11] Mabrouki F, Genest M, Shi G and Fahr A, "Numerical modeling for thermographic inspection of fibre metal laminates”, J. NDT and E International, Vol. 42, pp. 581-588, 2009.
[12] Maldague X, "Theory and practice of infrared technology for nondestructive testing” Wiley-Interscience, New York. 453 – 525, 2001.
[13] Meola C, Givanni M.C, Squillace A and Vitiello A, "Non-destructive evaluation of aerospace materials with lock-in thermography” J. Engineering Failure Analysis, Vol. 13. No. 3, pp. 380-388, 2006.
[14] Mirela S, Ibrarra-Castanedo, Maldague X, Bendada A, Svaic S and Boras I, "Pulse thermography applied on a complex structure sample: comparison and analysis of numerical and experimental results”, IV conferencia Panamericana de END, Buenos Aires, 2007.
[15] Muralidhar C and Arya N.K, "Evaluation of defects in axisymmetric composite structures by thermography”, NDT&E International, Vol. 26. No. 4, pp. 198-193, 1993.
[16] Muzia G, Rdzawski Z.M, Rojek M, Stabik J and Wróbel G, "Thermographic diagnosis of fatigue degradation of epoxy-glass composites”, Journal of Achievements in Materials and Manufacturing Engineering, Vol. 24. No. 2, pp. 123-126, 2007.
[17] Omar M, Hassan M, Saito K and Alloo R, "IR self-referencing thermography for detection of in-depth defects”, Journal of Infrared Physics and Technology, 46(4), pp 283-289, 2005.
[18] Omar M, Haassan M, Donohue K, Saito K and Alloo R, "Infrared thermography for inspecting the adhesion integrity of plastic welded joints”, NDT and E International, Vol. 39, pp. 1-7, 2006.
[19] Peter linde, Jürgen pleitner, Henk de boer and Jos sinke, "Numerical and experimental simulation of damage behaviour of fibre metal laminates”, 24th international congress of the aeronautical sciences, ICAS 2004.
[20] Qiaojian Huang, Regez Brad, Krishnaswamy and Sridhar, "The influence of disbond defects on Lamb wave testing in GLARE composites” Proceedings of the SPIE, 2010, Vol. 7650, pp. 76502P-76502P-8.
[21] Saintey M B and Almond D P, "Defect Sizing by Transient Thermography II: A Numerical Treatment”, Journal of physics. D, Applied physics, Vol. 28, pp. 2539-2546,1995.
[22] Speer. and Es-Said. 2004. Applications of an aluminum–beryllium composite for structural aerospace components, Engineering Failure Analysis, Vol. 11. No. 6, pp. 895–902.
[23] Sundaravalli S, Vijayaraghavan G.K. and Majumder M.C. "Estimation of required heat input for the evaluation of Disbonds in FMLs Using Thermography”, International Conference on Modeling, Optimization and Computing (ICMOC 2010), National Institute of Technology, Durgapur, India, October 28 - 30, 2010, American Institute of Physics (AIP) Conference Proceedings, Vol. 1298, pp 129-134. ISBN: 978-0-7354-0854-8
[24] Sundaravalli S, Majumder M and Vijayaraghavan G.K "Numerical Analysis of Defects in FML using Through-Transmission Mode of Active Thermography”, Journal of Engineering Trends and Technology, Vol. 3. No. 3, pp 437-447, 2012.
[25] Timothy B Roth and Ann M. Anderson, "A Light Transmission Based Liquid Crystal Thermography System,” Journal of Heat Transfer, Vol. 30. No.1, 2008.
[26] Vageswar A, Balasubramaniam K, Krishnamurthy C.V, Jayakumar T and Raj B, "Periscope infrared thermography for local wall thinning in tubes”, NDT&E International, 42 (4), pp 275–282, 2009.
[27] Vijayaraghavan G K, Majumder M.C and Ramachandran K.P, "Quantitative Analysis of Delaminations in GRP Pipes Using Thermal NDTE Technique”, Journal of Advanced Research in Mechanical Engineering, Vol. 1. No. 1, pp.60-68, 2010.
[28] Vijayaraghavan G.K. and Sundaravalli S "Evaluation of Pits in GRP Composite Pipes by Thermal NDT Technique”. Journal of Reinforced Plastics and Composites, 30 (19), pp 1599–1604, 2011.
[29] Sundaravalli S, Majumder M.C and Vijayaraghavan G.K "Numerical Analyses of Defects in FML using Through-Transmission Mode of Active THermograpghy”, International journal of Engineering and Technology, 3(3), pp 437-447, 2012.
Vol:13 No:05 2019Vol:13 No:04 2019Vol:13 No:03 2019Vol:13 No:02 2019Vol:13 No:01 2019
Vol:12 No:12 2018Vol:12 No:11 2018Vol:12 No:10 2018Vol:12 No:09 2018Vol:12 No:08 2018Vol:12 No:07 2018Vol:12 No:06 2018Vol:12 No:05 2018Vol:12 No:04 2018Vol:12 No:03 2018Vol:12 No:02 2018Vol:12 No:01 2018
Vol:11 No:12 2017Vol:11 No:11 2017Vol:11 No:10 2017Vol:11 No:09 2017Vol:11 No:08 2017Vol:11 No:07 2017Vol:11 No:06 2017Vol:11 No:05 2017Vol:11 No:04 2017Vol:11 No:03 2017Vol:11 No:02 2017Vol:11 No:01 2017
Vol:10 No:12 2016Vol:10 No:11 2016Vol:10 No:10 2016Vol:10 No:09 2016Vol:10 No:08 2016Vol:10 No:07 2016Vol:10 No:06 2016Vol:10 No:05 2016Vol:10 No:04 2016Vol:10 No:03 2016Vol:10 No:02 2016Vol:10 No:01 2016
Vol:9 No:12 2015Vol:9 No:11 2015Vol:9 No:10 2015Vol:9 No:09 2015Vol:9 No:08 2015Vol:9 No:07 2015Vol:9 No:06 2015Vol:9 No:05 2015Vol:9 No:04 2015Vol:9 No:03 2015Vol:9 No:02 2015Vol:9 No:01 2015
Vol:8 No:12 2014Vol:8 No:11 2014Vol:8 No:10 2014Vol:8 No:09 2014Vol:8 No:08 2014Vol:8 No:07 2014Vol:8 No:06 2014Vol:8 No:05 2014Vol:8 No:04 2014Vol:8 No:03 2014Vol:8 No:02 2014Vol:8 No:01 2014
Vol:7 No:12 2013Vol:7 No:11 2013Vol:7 No:10 2013Vol:7 No:09 2013Vol:7 No:08 2013Vol:7 No:07 2013Vol:7 No:06 2013Vol:7 No:05 2013Vol:7 No:04 2013Vol:7 No:03 2013Vol:7 No:02 2013Vol:7 No:01 2013
Vol:6 No:12 2012Vol:6 No:11 2012Vol:6 No:10 2012Vol:6 No:09 2012Vol:6 No:08 2012Vol:6 No:07 2012Vol:6 No:06 2012Vol:6 No:05 2012Vol:6 No:04 2012Vol:6 No:03 2012Vol:6 No:02 2012Vol:6 No:01 2012
Vol:5 No:12 2011Vol:5 No:11 2011Vol:5 No:10 2011Vol:5 No:09 2011Vol:5 No:08 2011Vol:5 No:07 2011Vol:5 No:06 2011Vol:5 No:05 2011Vol:5 No:04 2011Vol:5 No:03 2011Vol:5 No:02 2011Vol:5 No:01 2011
Vol:4 No:12 2010Vol:4 No:11 2010Vol:4 No:10 2010Vol:4 No:09 2010Vol:4 No:08 2010Vol:4 No:07 2010Vol:4 No:06 2010Vol:4 No:05 2010Vol:4 No:04 2010Vol:4 No:03 2010Vol:4 No:02 2010Vol:4 No:01 2010
Vol:3 No:12 2009Vol:3 No:11 2009Vol:3 No:10 2009Vol:3 No:09 2009Vol:3 No:08 2009Vol:3 No:07 2009Vol:3 No:06 2009Vol:3 No:05 2009Vol:3 No:04 2009Vol:3 No:03 2009Vol:3 No:02 2009Vol:3 No:01 2009
Vol:2 No:12 2008Vol:2 No:11 2008Vol:2 No:10 2008Vol:2 No:09 2008Vol:2 No:08 2008Vol:2 No:07 2008Vol:2 No:06 2008Vol:2 No:05 2008Vol:2 No:04 2008Vol:2 No:03 2008Vol:2 No:02 2008Vol:2 No:01 2008
Vol:1 No:12 2007Vol:1 No:11 2007Vol:1 No:10 2007Vol:1 No:09 2007Vol:1 No:08 2007Vol:1 No:07 2007Vol:1 No:06 2007Vol:1 No:05 2007Vol:1 No:04 2007Vol:1 No:03 2007Vol:1 No:02 2007Vol:1 No:01 2007