184
2615
Performance of Power System Stabilizer (UNITROL D) in Benghazi North Power Plant
Abstract: The use of power system stabilizers (PSSs) to damp
power system swing mode of oscillations is practical important. Our
purpose is to retune the power system stabilizer (PSS1A) parameters
in Unitrol D produced by ABB– was installed in 1995in Benghazi
North Power Plants (BNPPs) at General Electricity Company of
Libya (GECOL). The optimal values of the power system stabilizer
(PSS1A) parameters are determined off-line by a particle swarm
optimization technique (PSO). The objective is to damp the local and
inter-area modes of oscillations that occur following power system
disturbances. The retuned power system stabilizer (PSS1A) can cope
with large disturbance at different operating points and has enhanced
power system stability.
Digital Article Identifier (DAI):
183
2313
Conceptualization of the Attractive Work Environment and Organizational Activity for Humans in Future Deep Mines
Abstract: The purpose of this paper is to conceptualize a futureoriented
human work environment and organizational activity in
deep mines that entails a vision of good and safe workplace. Futureoriented
technological challenges and mental images required for
modern work organization design were appraised. It is argued that an
intelligent-deep-mine covering the entire value chain, including
environmental issues and with work organization that supports good
working and social conditions towards increased human productivity
could be designed. With such intelligent system and work
organization in place, the mining industry could be seen as a place
where cooperation, skills development and gender equality are key
components. By this perspective, both the youth and women might
view mining activity as an attractive job and the work environment
as a safe, and this could go a long way in breaking the unequal
gender balance that exists in most mines today.
Digital Article Identifier (DAI):
182
4618
A Multi-layer Artificial Neural Network Architecture Design for Load Forecasting in Power Systems
Abstract: In this paper, the modelling and design of artificial neural network architecture for load forecasting purposes is investigated. The primary pre-requisite for power system planning is to arrive at realistic estimates of future demand of power, which is known as Load Forecasting. Short Term Load Forecasting (STLF) helps in determining the economic, reliable and secure operating strategies for power system. The dependence of load on several factors makes the load forecasting a very challenging job. An over estimation of the load may cause premature investment and unnecessary blocking of the capital where as under estimation of load may result in shortage of equipment and circuits. It is always better to plan the system for the load slightly higher than expected one so that no exigency may arise. In this paper, a load-forecasting model is proposed using a multilayer neural network with an appropriately modified back propagation learning algorithm. Once the neural network model is designed and trained, it can forecast the load of the power system 24 hours ahead on daily basis and can also forecast the cumulative load on daily basis. The real load data that is used for the Artificial Neural Network training was taken from LDC, Gujarat Electricity Board, Jambuva, Gujarat, India. The results show that the load forecasting of the ANN model follows the actual load pattern more accurately throughout the forecasted period.
Digital Article Identifier (DAI):
181
7649
Nonstational Dual Wavelet Frames in Sobolev Spaces
Abstract: In view of the good properties of nonstationary wavelet frames and the better flexibility of wavelets in Sobolev spaces, the nonstationary dual wavelet frames in a pair of dual Sobolev spaces are studied in this paper. We mainly give the oblique extension principle and the mixed extension principle for nonstationary dual wavelet frames in a pair of dual Sobolev spaces Hs(Rd) and H-s(Rd).
Digital Article Identifier (DAI):
180
2411
Oscillation Theorems for Second-order Nonlinear Neutral Dynamic Equations with Variable Delays and Damping
Abstract: In this paper, we study the oscillation of a class of second-order nonlinear neutral damped variable delay dynamic equations on time scales. By using a generalized Riccati transformation technique, we obtain some sufficient conditions for the oscillation of the equations. The results of this paper improve and extend some known results. We also illustrate our main results with some examples.
Digital Article Identifier (DAI):
179
6145
The Effect of Increment in Simulation Samples on a Combined Selection Procedure
Abstract: Statistical selection procedures are used to select the
best simulated system from a finite set of alternatives. In this paper,
we present a procedure that can be used to select the best system
when the number of alternatives is large. The proposed procedure
consists a combination between Ranking and Selection, and Ordinal
Optimization procedures. In order to improve the performance of Ordinal
Optimization, Optimal Computing Budget Allocation technique
is used to determine the best simulation lengths for all simulation
systems and to reduce the total computation time. We also argue
the effect of increment in simulation samples for the combined
procedure. The results of numerical illustration show clearly the effect
of increment in simulation samples on the proposed combination of
selection procedure.
Digital Article Identifier (DAI):
178
8620
Li4SiO4 Prepared by Sol-gel Method as Potential Host for LISICON Structured Solid Electrolytes
Abstract: In this study, Li4SiO4 powder was successfully
synthesized via sol gel method followed by drying at 150oC. Lithium
oxide, Li2O and silicon oxide, SiO2 were used as the starting
materials with citric acid as the chelating agent. The obtained powder
was then sintered at various temperatures. Crystallographic phase
analysis, morphology and ionic conductivity were investigated
systematically employing X-ray diffraction, Fourier Transform
Infrared, Scanning Electron Microscopy and AC impedance
spectroscopy. XRD result showed the formation of pure monoclinic
Li4SiO4 crystal structure with lattice parameters a = 5.140 Å, b =
6.094 Å, c = 5.293 Å, β = 90o in the sample sintered at 750oC. This
observation was confirmed by FTIR analysis. The bulk conductivity
of this sample at room temperature was 3.35 × 10-6 S cm-1 and the
highest bulk conductivity of 1.16 × 10-4 S cm-1 was obtained at
100°C. The results indicated that, the Li4SiO4 compound has
potential to be used as host for LISICON structured solid electrolyte
for low temperature application.
Digital Article Identifier (DAI):
177
4583
Microstructure Parameters of a Super-Ionic Sample (Csag2i3)
Abstract: Sample of CsAg2I3 was prepared by solid state reaction. Then, microstructure parameters of this sample have been determined using wide angle X-ray scattering WAXS method. As well as, Cell parameters of crystal structure have been refined using CHEKCELL program. This analysis states that the lattice intrinsic strainof the sample is so small and the crystal size is on the order of 559Å.
Digital Article Identifier (DAI):
176
445
Thermal and Mechanical Buckling of Short and Long Functionally Graded Cylindrical Shells Using First Order Shear Deformation Theory
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.
Digital Article Identifier (DAI):
175
15274
A Chaotic Study on Tremor Behavior of Parkinsonian Patients under Deep Brain Stimulation
Abstract: Deep Brain Stimulation or DBS is a surgical treatment for Parkinson-s Disease with three stimulation parameters: frequency, pulse width, and voltage. The parameters should be selected appropriately to achieve effective treatment. This selection now, performs clinically. The aim of this research is to study chaotic behavior of recorded tremor of patients under DBS in order to present a computational method to recognize stimulation optimum voltage. We obtained some chaotic features of tremor signal, and discovered embedding space of it has an attractor, and its largest Lyapunov exponent is positive, which show tremor signal has chaotic behavior, also we found out, in optimal voltage, entropy and embedding space variance of tremor signal have minimum values in comparison with other voltages. These differences can help neurologists recognize optimal voltage numerically, which leads to reduce patients' role and discomfort in optimizing stimulation parameters and to do treatment with high accuracy.
Digital Article Identifier (DAI):
174
1975
Free Vibration Analysis of Functionally Graded Beams
Abstract: This work presents the highly accurate numerical calculation
of the natural frequencies for functionally graded beams with
simply supported boundary conditions. The Timoshenko first order
shear deformation beam theory and the higher order shear deformation
beam theory of Reddy have been applied to the functionally
graded beams analysis. The material property gradient is assumed
to be in the thickness direction. The Hamilton-s principle is utilized
to obtain the dynamic equations of functionally graded beams. The
influences of the volume fraction index and thickness-to-length ratio
on the fundamental frequencies are discussed. Comparison of the
numerical results for the homogeneous beam with Euler-Bernoulli
beam theory results show that the derived model is satisfactory.
Digital Article Identifier (DAI):
173
6869
Performance Analysis of Certificateless Signature for IKE Authentication
Abstract: Elliptic curve-based certificateless signature is slowly
gaining attention due to its ability to retain the efficiency of
identity-based signature to eliminate the need of certificate
management while it does not suffer from inherent private
key escrow problem. Generally, cryptosystem based on elliptic
curve offers equivalent security strength at smaller key sizes
compared to conventional cryptosystem such as RSA which
results in faster computations and efficient use of computing
power, bandwidth, and storage. This paper proposes to implement
certificateless signature based on bilinear pairing to
structure the framework of IKE authentication. In this paper,
we perform a comparative analysis of certificateless signature
scheme with a well-known RSA scheme and also present the
experimental results in the context of signing and verification
execution times. By generalizing our observations, we discuss the
different trade-offs involved in implementing IKE authentication
by using certificateless signature.
Digital Article Identifier (DAI):
172
13358
Effect of CW Laser Annealing on Silicon Surface for Application of Power Device
Authors: Satoru Kaneko,
Takeshi Ito,
Kensuke Akiyama,
Manabu Yasui,
Chihiro Kato,
Satomi Tanaka,
Yasuo Hirabayashi,
Takeshi Ozawa,
Akira Matsuno,
Takashi Nire,
Hiroshi Funakubo,
Mamoru Yoshimoto
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Digital Article Identifier (DAI):
171
14152
The Residual Effects of Different Doses of Atrazine+Alachlor and Foramsulfuron on the Growth and Physiology of Rapeseed (Brassica napus L.)
Abstract: A pot experiment was carried out under controlled
conditions to evaluate the residual effects of different doses of
atrazine+alachlor and foramsulfuron used in corn fields on the
growth and physiology of rapeseed (Brassica napus L.). A split-plot
experiment in CRD with 4 replications was used. The main plots
consisted of herbicide type (atrazine+alachlor mixture and
foramsulfuron) and the sub-plots were different residual doses of the
herbicides (0, 1%, 5%, 10%, 20%, 40%, 50% and 100%). 7 cm
diameter pots were filled with a virgin soil and seeds of rapeseed cv.
Hayola were planted in them. The pots were kept under controlled
conditions for 8 weeks after germination. At harvest, the growth
parameters and the chlorophyll contents of the leaves were
determined. The results showed that the growth of rapeseed plants
was completely prevented at the highest residual doses of the
herbicides (50 and 100 %). The growth parameters of rapeseed plants
were affected by all doses of both types of the herbicide as compared
to the controls. The residual effects of atrazine+alachlor mixture in
reducing the growth parameters of rapeseed were more pronounced
as compared to the residual effects of foramsulfuron alone.
Digital Article Identifier (DAI):
170
7194
The Performance Analysis of Valveless Micropump with Contoured Nozzle/Diffuser
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Digital Article Identifier (DAI):
169
5730
Artificial Intelligence Model to Predict Surface Roughness of Ti-15-3 Alloy in EDM Process
Abstract: Conventionally the selection of parameters depends
intensely on the operator-s experience or conservative technological
data provided by the EDM equipment manufacturers that assign
inconsistent machining performance. The parameter settings given by
the manufacturers are only relevant with common steel grades. A
single parameter change influences the process in a complex way.
Hence, the present research proposes artificial neural network (ANN)
models for the prediction of surface roughness on first commenced
Ti-15-3 alloy in electrical discharge machining (EDM) process. The
proposed models use peak current, pulse on time, pulse off time and
servo voltage as input parameters. Multilayer perceptron (MLP) with
three hidden layer feedforward networks are applied. An assessment
is carried out with the models of distinct hidden layer. Training of the
models is performed with data from an extensive series of
experiments utilizing copper electrode as positive polarity. The
predictions based on the above developed models have been verified
with another set of experiments and are found to be in good
agreement with the experimental results. Beside this they can be
exercised as precious tools for the process planning for EDM.
Digital Article Identifier (DAI):
168
1688
Field Emission Properties of Multi-wall Carbon Nanotube Field Emitters using Graphite Tip by Electroporetic Deposition
Abstract: We fabricated multi-walled carbon nanotube (MCNT)
emitters by an electroporetic deposition (EPD) method using a
MCNT-sodium dodecyl sulfate (SDS) suspension. MCNT films were
prepared on graphite tip using EPD. We observe field emission
properties of MCNT film after heat treatment. Consequently, The
MCNT film on graphite tip exhibit good electron emission current.
Digital Article Identifier (DAI):
167
14454
Investigating the Effectiveness of Self-Shading Strategy on Overall Thermal Transfer Value and Window Size in High Rise Buildings
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Digital Article Identifier (DAI):
166
11800
Reflections of Prospective Teachers Toward a Critical Thinking-Based Pedagogical Course: A Case Study
Abstract: Promoting critical thinking (CT) in an educational
setting has been appraised in order to enhance learning and
intellectual skills. In this study, a pedagogical course in a vocational
teacher education program in Turkey was designed by integrating CT
skill-based strategies/activities into the course content and CT skills
were means leading to intended course objectives. The purpose of the
study was to evaluate the importance of the course objectives, the
attainment of the objectives, and the effectiveness of teachinglearning
strategies/activities from prospective teachers- points of
view. The results revealed that although the students mostly
considered the course objectives important, they did not feel
competent in the attainment of all objectives especially in those
related to the main topic of Learning and those requiring higher order
thinking skills. On the other hand, the students considered the course
activities effective for learning and for the development of thinking
skills, especially, in interpreting, comparing, questioning,
contrasting, and forming relationships.
Digital Article Identifier (DAI):
165
11039
Tourist Satisfaction and Repeat Visitation; Toward a New Comprehensive Model
Abstract: Tourism researchers have recently focused on repeat visitation as a part of destination loyalty. Different models have also considered satisfaction as the main determinant of revisit intention, while findings in many studies show it as a continuous issue. This conceptual paper attempts at evaluating recent empirical studies on satisfaction and revisit intention. Based on limitations and gaps in recent studies, the current paper suggests a new model that would be more comprehensive than those in previous studies. The new model offers new relationships between antecedents (destination image, perceived value, specific novelty seeking, and distance to destination) and both of satisfaction and revisit intention. Revisit intention in turn is suggested to be measured in a temporal approach.
Digital Article Identifier (DAI):
164
15083
Taiwan Sugar Corporation's Participation in the Mechanism of Payment for Environmental Services (PES)
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC's participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC’s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC’s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC's consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC’s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Digital Article Identifier (DAI):
163
7521
Trends, Problems and Needs of Urban Housing in Malaysia
Abstract: The right to housing is a basic need while good
quality and affordable housing is a reflection of a high quality of life.
However, housing remains a major problem for most, especially for
the bottom billions. Satisfaction on housing and neighbourhood
conditions are one of the important indicators that reflect quality of
life. These indicators are also important in the process of evaluating
housing policy with the objective to increase the quality of housing
and neighbourhood. The research method is purely based on a
quantitative method, using a survey. The findings show that housing
purchasing trend in urban Malaysia is determined by demographic
profiles, mainly by education level, age, gender and income. The
period of housing ownership also influenced the socio-cultural
interactions and satisfaction of house owners with their
neighbourhoods. The findings also show that the main concerns for
house buyers in urban areas are price and location of the house.
Respondents feel that houses in urban Malaysia is too expensive and
beyond their affordability. Location of houses and distance from
work place are also regarded as the main concern. However,
respondents are fairly satisfied with religious and socio-cultural
facilities in the housing areas and most importantly not many regard
ethnicity as an issue in their decision-making, when buying a house.
Digital Article Identifier (DAI):
162
4658
Migration among Multicities
Abstract: This paper proposes a simple model of economic geography within the Dixit-Stiglitz-Iceberg framework that may be used to analyze migration patterns among three cities. The cost–benefit tradeoffs affecting incentives for three types of migration, including echelon migration, are discussed. This paper develops a tractable, heterogeneous-agent, general equilibrium model, where agents share constant human capital, and explores the relationship between the benefits of echelon migration and gross human capital. Using Chinese numerical solutions, we study the manifestation of echelon migration and how it responds to changes in transportation cost and elasticity of substitution. Numerical results demonstrate that (i) there are positive relationships between a migration-s benefit-and-wage ratio, (ii) there are positive relationships between gross human capital ratios and wage ratios as to origin and destination, and (iii) we identify 13 varieties of human capital convergence among cities. In particular, this model predicts population shock resulting from the processes of migration choice and echelon migration.
Digital Article Identifier (DAI):
161
5478
Trade Openness and Its Effects on Economic Growth in Selected South Asian Countries: A Panel Data Study
Abstract: The study investigates the causal link between trade
openness and economic growth for four South Asian countries for
period 1972-1985 and 1986-2007 to examine the scenario before and
after the implementation of SAARC. Panel cointegration and
FMOLS techniques are employed for short run and long run
estimates. In 1972-85 short run unidirectional causality from GDP to
openness is found whereas, in 1986-2007 there exists bi-directional
causality between GDP and openness. The long run elasticity
magnitude between GDP and openness contains negative sign in
1972-85 which shows that there exists long run negative relationship.
While in time period 1986-2007 the elasticity magnitude has positive
sign that indicates positive causation between GDP and openness. So
it can be concluded that after the implementation of SAARC overall
situation of selected countries got better. Also long run coefficient of
error term suggests that short term equilibrium adjustments are driven
by adjustment back to long run equilibrium.
Digital Article Identifier (DAI):
160
13767
Modern /Post-Modern Paradigm and the Current Reflections on Residential Building Exteriors in Cyprus
Abstract: The main aim of this paper was to investigate the
existing architecture in Cyprus, and thus identify and describe the
overall architectural rationale of the built environment. In Cyprus,
where individuals live in a society that reflects postmodern
paradigms rather than modern ones, the existing built environment
has many different reflections of the structure of its society.
Digital Article Identifier (DAI):
159
8437
Usability Evaluation of Online News Websites: A User Perspective Approach
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.
Digital Article Identifier (DAI):
158
8575
The Organizational Innovativeness of Public-Listed Housing Developers
Abstract: This paper investigated the organizational
innovativeness of public listed housing developers in Malaysia. We
conceptualized organizational innovativeness as a multi-dimensional
construct consisting of 5 dimensions: market innovativeness, product
innovativeness, process innovativeness, behavior innovativeness and
strategic innovativeness. We carried out questionnaire survey with all
accessible public listed developers in Malaysia and received a 56
percent response. We found that the innovativeness of public listed
housing developers is low. The study extends the knowledge on
innovativeness theory by using a multi-dimensional contructs to
conceptualize the innovativeness of public listed housing developers
in Malaysia where all this while most studies focused on single
dimensional construct of innovativeness. The paper ends by
providing some explanations for the results.
Digital Article Identifier (DAI):
157
12225
Do C-Test and Cloze Procedure Measure what they Purport to be Measuring? A Case of Criterion-Related Validity
Abstract: This article investigated the validity of C-test and Cloze test which purport to measure general English proficiency. To provide empirical evidence pertaining to the validity of the interpretations based on the results of these integrative language tests, their criterion-related validity was investigated. In doing so, the test of English as a foreign language (TOEFL) which is an established, standardized, and internationally administered test of general English proficiency was used as the criterion measure. Some 90 Iranian English majors participated in this study. They were seniors studying English at a university in Tehran, Iran. The results of analyses showed that there is a statistically significant correlation among participants- scores on Cloze test, C-test, and the TOEFL. Building on the findings of the study and considering criterion-related validity as the evidential basis of the validity argument, it was cautiously deducted that these tests measure the same underlying trait. However, considering the limitations of using criterion measures to validate tests, no absolute claims can be made as to the construct validity of these integrative tests.
Digital Article Identifier (DAI):
156
5231
Impact of Revenue Gap on Budget Deficit, Debt Burden and Economic Growth: An Evidence from Pakistan
Abstract: Availability and mobilization of revenue is the main
essential with which an economy is managed and run. While
planning or while making the budgets nations set revenue targets to
be achieved. But later when the accounts are closed the actual
collections of revenue through taxes or even the non-tax revenue
collection would invariably be different as compared to the initial
estimates and targets set to be achieved. This revenue-gap distorts the
whole system and the economy disturbing all the major macroeconomic
indicators. This study is aimed to find out short and long
term impact of revenue gap on budget deficit, debt burden and
economic growth on the economy of Pakistan. For this purpose the
study uses autoregressive distributed lag approach to cointegration
and error correction mechanism on three different models for the
period 1980 to 2009. The empirical results show that revenue gap has
a short and long run relationship with economic growth and budget
deficit. However, revenue gap has no impact on debt burden.
Digital Article Identifier (DAI):
155
6809
Physical Evaluation of Selected Malaysian National Rugby Players
Abstract: Currently, there is no database or local norms for the
physical performance of Malaysian rugby players. This database or
norms are vital for Malaysian-s sports development as programs can
be setup to improve the current status. This pilot study was
conducted to evaluate the status of our semi professional rugby
players. The rugby players were randomly selected from the
Malaysian National team and several clubs in the Klang valley, Kuala
Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years)
were selected for this pilot study. Height, bodyweight, percentage
body fat and body mass index (BMI) and several other physical tests
were performed. Results from the BLEEP test revealed an average of
level 9, shuttle 2 for the players. Interestingly, forwards were taller,
heavier, and had lower maximal aerobic power than backs in the
same team. In conclusion, the physical characteristics of the rugby
players were much lower when compared to international players
from other countries. From this pilot study, the physical performance
of the Malaysian team must be improved in order to further develop
the sports.
Digital Article Identifier (DAI):
154
13012
The Strange Relationship between Literacy and Well-Being: The Results of an International Survey with Special Focus on Italy
Abstract: Does education matter to the quality of our life? The results of extensive studies offer an affirmative answer to this question: high education levels are positively associated with higher income, with more highly qualified professions, with lower risk of unemployment, with better physical health and also, it is said, with more happiness. However, exploring these relationships is far from straightforward. Aside from educational credentials, what properties distinguish functionally literate individuals? How can their personal level of satisfaction be measured? What are the social mechanisms whereby education affects well-being?Using a literacy index and several measures for well-being developed by secondary analysis of the Adult Literacy and Life Skills Survey database, this investigation examined the relationship between literacy skills and subjective wellbeing in several OECD (Organisation for Economic Co-operation and Development) countries. Special attention was been addressed to Italy, and in particular to two regions representing territorial differences in this country: Piedmont and Campania.
Digital Article Identifier (DAI):
153
12254
Predicting Individual Investors- Intention to Invest: An Experimental Analysis of Attitude as a Mediator
Abstract: The survival of publicly listed companies largely
depends on their stocks being liquidly traded. This goal can be
achieved when new investors are attracted to invest on companies-
stocks. Among different groups of investors, individual investors are
generally less able to objectively evaluate companies- risks and
returns, and tend to be emotionally biased in their investing
decisions. Therefore their decisions may be formed as a result of
perceived risks and returns, and influenced by companies- images.
This study finds that perceived risk, perceived returns and trust
directly affect individual investors- trading decisions while attitude
towards brand partially mediates the relationships. This finding
suggests that, in courting individual investors, companies still need to
perform financially while building a good image can result in their
stocks being accepted quicker than the stocks of good performing
companies with hidden images.
Digital Article Identifier (DAI):
152
15329
Comparison of Detached Eddy Simulations with Turbulence Modeling
Abstract: Flow field around hypersonic vehicles is very
complex and difficult to simulate. The boundary layers are squeezed
between shock layer and body surface. Resolution of boundary layer,
shock wave and turbulent regions where the flow field has high
values is difficult of capture. Detached eddy simulation (DES) is a
modification of a RANS model in which the model switches to a
subgrid scale formulation in regions fine enough for LES
calculations. Regions near solid body boundaries and where the
turbulent length scale is less than the maximum grid dimension are
assigned the RANS mode of solution. As the turbulent length scale
exceeds the grid dimension, the regions are solved using the LES
mode. Therefore the grid resolution is not as demanding as pure LES,
thereby considerably cutting down the cost of the computation. In
this research study hypersonic flow is simulated at Mach 8 and
different angle of attacks to resolve the proper boundary layers and
discontinuities. The flow is also simulated in the long wake regions.
Mesh is little different than RANS simulations and it is made dense
near the boundary layers and in the wake regions to resolve it
properly. Hypersonic blunt cone cylinder body with frustrum at angle
5o and 10 o are simulated and there aerodynamics study is performed
to calculate aerodynamics characteristics of different geometries. The
results and then compared with experimental as well as with some
turbulence model (SA Model). The results achieved with DES
simulation have very good resolution as well as have excellent
agreement with experimental and available data. Unsteady
simulations are performed for DES calculations by using duel time
stepping method or implicit time stepping. The simulations are
performed at Mach number 8 and angle of attack from 0o to 10o for
all these cases. The results and resolutions for DES model found
much better than SA turbulence model.
Digital Article Identifier (DAI):
151
5669
Unsteady Transonic Aerodynamic Analysis for Oscillatory Airfoils using Time Spectral Method
Abstract: This research proposes an algorithm for the simulation
of time-periodic unsteady problems via the solution unsteady Euler
and Navier-Stokes equations. This algorithm which is called Time
Spectral method uses a Fourier representation in time and hence
solve for the periodic state directly without resolving transients
(which consume most of the resources in a time-accurate scheme).
Mathematical tools used here are discrete Fourier transformations. It
has shown tremendous potential for reducing the computational cost
compared to conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy. The accuracy and efficiency of this technique is
verified by Euler and Navier-Stokes calculations for pitching airfoils.
Because of flow turbulence nature, Baldwin-Lomax turbulence
model has been used at viscous flow analysis. The results presented
by the Time Spectral method are compared with experimental data. It
has shown tremendous potential for reducing the computational cost
compared to the conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy, because results verify the small number of time
intervals per pitching cycle required to capture the flow physics.
Digital Article Identifier (DAI):
150
15390
Cold Flow Investigation of Primary Zone Characteristics in Combustor Utilizing Axial Air Swirler
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.
Digital Article Identifier (DAI):
149
9844
Performance Analysis of Heat Pipe Using Copper Nanofluid with Aqueous Solution of n-Butanol
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Digital Article Identifier (DAI):
148
8251
Active Fiber Composites for Smart Damping of Doubly Curved Laminated Shells
Abstract: This paper deals with the analysis of active constrained layer damping (ACLD) of doubly curved laminated composite shells using active fiber composite (AFC) materials. The constraining layer of the ACLD treatment has been considered to be made of the AFC materials. A three dimensional energy based finite element model of the smart doubly curved laminated composite shell integrated with a patch of such ACLD treatment has been developed to demonstrate the performance of the patch on enhancing the damping characteristics of the doubly curved laminated composite shells. Particular emphasis has been placed on studying the effect of variation of piezoelectric fiber orientation angle in the constraining AFC layer on the control authority of the ACLD patch.
Digital Article Identifier (DAI):
147
11453
Effects of Input Speed on the Dynamic Response of Planar Multi-body Systems with Differently Located Frictionless Revolute Clearance Joints
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.
Digital Article Identifier (DAI):
146
9829
Plastic Flow through Taper Dies: A Threedimensional Analysis
Abstract: The plastic flow of metal in the extrusion process is
an important factor in controlling the mechanical properties of the
extruded products. It is, however, difficult to predict the metal flow
in three dimensional extrusions of sections due to the involvement of
re-entrant corners. The present study is to find an upper bound
solution for the extrusion of triangular sectioned through taper dies
from round sectioned billet. A discontinuous kinematically
admissible velocity field (KAVF) is proposed. From the proposed
KAVF, the upper bound solution on non-dimensional extrusion
pressure is determined with respect to the chosen process parameters.
The theoretical results are compared with experimental results to
check the validity of the proposed velocity field. An extrusion setup
is designed and fabricated for the said purpose, and all extrusions are
carried out using circular billets. Experiments are carried out with
commercially available lead at room temperature.
Digital Article Identifier (DAI):
145
9945
Determination of Q and R Matrices for Optimal Pitch Aircraft Control
Abstract: In this paper, the process of obtaining Q and R
matrices for optimal pitch aircraft control system has been described.
Since the innovation of optimal control method, the determination of
Q and R matrices for such system has not been fully specified. The
value of Q and R for optimal pitch aircraft control application, have
been simulated and calculated. The suitable results for Q and R have
been observed through the performance index (PI). If the PI is small
“enough", we would say the Q & R values are suitable for that
certain type of optimal control system. Moreover, for the same value
of PI, we could have different Q and R sets. Due to the rule-free
determination of Q and R matrices, a specific method is brought to
find out the rough value of Q and R referring to rather small value of
PI.
Digital Article Identifier (DAI):
144
1142
Hydrogen Embrittlement in a Coupled Mass Diffusion with Stress near a Blunting Crack Tip for AISI 4135 Pressure Vessel
Abstract: In pressure vessels contain hydrogen, the role of
hydrogen will be important because of hydrogen cracking problem. It
is difficult to predict what is happened in metallurgical field spite of a
lot of studies have been searched. The main role in controlling the
mass diffusion as driving force is related to stress. In this study, finite
element analysis is implemented to estimate material-s behavior
associated with hydrogen embrittlement. For this purpose, one model
of a pressure vessel is introduced that it has definite boundary and
initial conditions. In fact, finite element is employed to solve the
sequentially coupled mass diffusion with stress near a crack front in a
pressure vessel. Modeling simulation intergrarnular fracture of AISI
4135 steel due to hydrogen is investigated. So, distribution of
hydrogen and stress are obtained and they indicate that their
maximum amounts occur near the crack front. This phenomenon is
happened exactly the region between elastic and plastic field.
Therefore, hydrogen is highly mobile and can diffuse through crystal
lattice so that this zone is potential to trap high volume of hydrogen.
Consequently, crack growth and fast fracture will be happened.
Digital Article Identifier (DAI):
143
5659
Effect of Welding Processes on Fatigue Properties of Ti-6Al-4V Alloy Joints
Abstract: This paper reports the fatigue crack growth behaviour
of gas tungsten arc, electron beam and laser beam welded Ti-6Al-4V
titanium alloy. Centre cracked tensile specimens were prepared to
evaluate the fatigue crack growth behaviour. A 100kN servo
hydraulic controlled fatigue testing machine was used under constant
amplitude uniaxial tensile load (stress ratio of 0.1 and frequency of
10 Hz). Crack growth curves were plotted and crack growth
parameters (exponent and intercept) were evaluated. Critical and
threshold stress intensity factor ranges were also evaluated. Fatigue
crack growth behaviour of welds was correlated with mechanical
properties and microstructural characteristics of welds. Of the three
joints, the joint fabricated by laser beam welding exhibited higher
fatigue crack growth resistance due to the presence of fine lamellar
microstructure in the weld metal.
Digital Article Identifier (DAI):
142
10048
An Approach for Transient Response Calculation of large Nonproportionally Damped Structures using Component Mode Synthesis
Abstract: A minimal complexity version of component mode
synthesis is presented that requires simplified computer
programming, but still provides adequate accuracy for modeling
lower eigenproperties of large structures and their transient
responses. The novelty is that a structural separation into components
is done along a plane/surface that exhibits rigid-like behavior, thus
only normal modes of each component is sufficient to use, without
computing any constraint, attachment, or residual-attachment modes.
The approach requires only such input information as a few (lower)
natural frequencies and corresponding undamped normal modes of
each component. A novel technique is shown for formulation of
equations of motion, where a double transformation to generalized
coordinates is employed and formulation of nonproportional damping
matrix in generalized coordinates is shown.
Digital Article Identifier (DAI):
141
6353
Banach Lattices with Weak Dunford-Pettis Property
Abstract: We introduce and study the class of weak almost Dunford-Pettis operators. As an application, we characterize Banach lattices with the weak Dunford-Pettis property. Also, we establish some sufficient conditions for which each weak almost Dunford-Pettis operator is weak Dunford-Pettis. Finally, we derive some interesting results.
Digital Article Identifier (DAI):
140
15291
Periodic Solutions in a Delayed Competitive System with the Effect of Toxic Substances on Time Scales
Abstract: In this paper, the existence of periodic solutions of a delayed competitive system with the effect of toxic substances is investigated by using the Gaines and Mawhin,s continuation theorem of coincidence degree theory on time scales. New sufficient conditions are obtained for the existence of periodic solutions. The approach is unified to provide the existence of the desired solutions for the continuous differential equations and discrete difference equations. Moreover, The approach has been widely applied to study existence of periodic solutions in differential equations and difference equations.
Digital Article Identifier (DAI):
139
11185
Extending Global Full Orthogonalization method for Solving the Matrix Equation AXB=F
Abstract: In the present work, we propose a new method for
solving the matrix equation AXB=F . The new method can
be considered as a generalized form of the well-known global full
orthogonalization method (Gl-FOM) for solving multiple linear
systems. Hence, the method will be called extended Gl-FOM (EGl-
FOM). For implementing EGl-FOM, generalized forms of block
Krylov subspace and global Arnoldi process are presented. Finally,
some numerical experiments are given to illustrate the efficiency of
our new method.
Digital Article Identifier (DAI):
138
7635
Quasilinearization–Barycentric Approach for Numerical Investigation of the Boundary Value Fin Problem
Abstract: In this paper we improve the quasilinearization method by barycentric Lagrange interpolation because of its numerical stability and computation speed to achieve a stable semi analytical solution. Then we applied the improved method for solving the Fin problem which is a nonlinear equation that occurs in the heat transferring. In the quasilinearization approach the nonlinear differential equation is treated by approximating the nonlinear terms by a sequence of linear expressions. The modified QLM is iterative but not perturbative and gives stable semi analytical solutions to nonlinear problems without depending on the existence of a smallness parameter. Comparison with some numerical solutions shows that the present solution is applicable.
Digital Article Identifier (DAI):
137
15645
An eighth order Backward Differentiation Formula with Continuous Coefficients for Stiff Ordinary Differential Equations
Abstract: A block backward differentiation formula of uniform
order eight is proposed for solving first order stiff initial value
problems (IVPs). The conventional 8-step Backward Differentiation
Formula (BDF) and additional methods are obtained from the same
continuous scheme and assembled into a block matrix equation which
is applied to provide the solutions of IVPs on non-overlapping
intervals. The stability analysis of the method indicates that the
method is L0-stable. Numerical results obtained using the proposed
new block form show that it is attractive for solutions of stiff problems
and compares favourably with existing ones.
Digital Article Identifier (DAI):
136
8347
High Accuracy Eigensolutions in Elasticity for Boundary Integral Equations by Nyström Method
Abstract: Elastic boundary eigensolution problems are converted
into boundary integral equations by potential theory. The kernels of
the boundary integral equations have both the logarithmic and Hilbert
singularity simultaneously. We present the mechanical quadrature
methods for solving eigensolutions of the boundary integral equations
by dealing with two kinds of singularities at the same time. The methods
possess high accuracy O(h3) and low computing complexity. The
convergence and stability are proved based on Anselone-s collective
compact theory. Bases on the asymptotic error expansion with odd
powers, we can greatly improve the accuracy of the approximation,
and also derive a posteriori error estimate which can be used for
constructing self-adaptive algorithms. The efficiency of the algorithms
are illustrated by numerical examples.
Digital Article Identifier (DAI):
135
9430
Approximately Jordan Maps and Their Stability
Abstract: In this paper we consider the approximate Jordan maps and boundedness of these maps. Also we investigate the stability of approximate Jordan maps and prove some stability properties for approximate Jordan maps.
Digital Article Identifier (DAI):
134
7039
Application of He’s Parameter-Expansion Method to a Coupled Van Der Pol oscillators with Two Kinds of Time-delay Coupling
Abstract: In this paper, the dynamics of a system of two van der Pol oscillators with delayed position and velocity is studied. We provide an approximate solution for this system using parameterexpansion method. Also, we obtain approximate values for frequencies of the system. The parameter-expansion method is more efficient than the perturbation method for this system because the method is independent of perturbation parameter assumption.
Digital Article Identifier (DAI):
133
12041
Preconditioned Mixed-Type Splitting Iterative Method For Z-Matrices
Abstract: In this paper, we present the preconditioned mixed-type
splitting iterative method for solving the linear systems, Ax = b,
where A is a Z-matrix. And we give some comparison theorems
to show that the convergence rate of the preconditioned mixed-type
splitting iterative method is faster than that of the mixed-type splitting
iterative method. Finally, we give a numerical example to illustrate
our results.
Digital Article Identifier (DAI):
132
11246
Heat and Mass Transfer over an Unsteady Stretching Surface Embedded in a Porous Medium in the Presence of Variable Chemical Reaction
Abstract: The effect of variable chemical reaction on heat and mass transfer characteristics over unsteady stretching surface embedded in a porus medium is studied. The governing time dependent boundary layer equations are transformed into ordinary differential equations containing chemical reaction parameter, unsteadiness parameter, Prandtl number and Schmidt number. These equations have been transformed into a system of first order differential equations. MATHEMATICA has been used to solve this system after obtaining the missed initial conditions. The velocity gradient, temperature, and concentration profiles are computed and discussed in details for various values of the different parameters.
Digital Article Identifier (DAI):
131
9287
Bifurcation Method for Solving Positive Solutions to a Class of Semilinear Elliptic Equations and Stability Analysis of Solutions
Abstract: Semilinear elliptic equations are ubiquitous in natural sciences. They give rise to a variety of important phenomena in quantum mechanics, nonlinear optics, astrophysics, etc because they have rich multiple solutions. But the nontrivial solutions of semilinear equations are hard to be solved for the lack of stabilities, such as Lane-Emden equation, Henon equation and Chandrasekhar equation. In this paper, bifurcation method is applied to solving semilinear elliptic equations which are with homogeneous Dirichlet boundary conditions in 2D. Using this method, nontrivial numerical solutions will be computed and visualized in many different domains (such as square, disk, annulus, dumbbell, etc).
Digital Article Identifier (DAI):
130
11521
The Partial Non-combinatorially Symmetric N10 -Matrix Completion Problem
Abstract: An n×n matrix is called an N1 0 -matrix if all principal minors are non-positive and each entry is non-positive. In this paper, we study the partial non-combinatorially symmetric N1 0 -matrix completion problems if the graph of its specified entries is a transitive tournament or a double cycle. In general, these digraphs do not have N1 0 -completion. Therefore, we have given sufficient conditions that guarantee the existence of the N1 0 -completion for these digraphs.
Digital Article Identifier (DAI):
129
3262
Existence of Solution for Singular Two-point Boundary Value Problem of Second-order Differential Equation
Abstract: In this paper, by constructing a special set and utilizing fixed point theory in coin, we study the existence of solution of singular two point’s boundary value problem for second-order differential equation, which improved and generalize the result of related paper.
Digital Article Identifier (DAI):
128
11250
Users- Motivation and Satisfaction with IS
Abstract: To motivate users to adopt and use information
systems effectively, the nature of motivation should be carefully
investigated. People are usually motivated within ongoing processes
which include a chain of states such as perception, stimulation,
motivation, actions and reactions and finally, satisfaction. This study
assumes that the relevant motivation processes should be executed in
a proper and continuous manner to be able to persistently motivate
and re-motivate people in organizational settings and towards
information systems. On this basis, the study attempts to propose
possible relationships between this process-nature view of
motivation in terms of the common chain of states and the nearly
unique properties of information systems as is perceived by users in
the sense of a knowledgeable and authoritative entity. In the
conclusion section, some guidelines for practitioners are suggested to
ease their tasks for motivating people to adopt and use information
systems.
Digital Article Identifier (DAI):
127
12900
Simultaneous Optimization of Machining Parameters and Tool Geometry Specifications in Turning Operation of AISI1045 Steel
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Digital Article Identifier (DAI):
126
11334
Using FEM for Prediction of Thermal Post-Buckling Behavior of Thin Plates During Welding Process
Abstract: Arc welding is an important joining process widely used in many industrial applications including production of automobile, ships structures and metal tanks. In welding process, the moving electrode causes highly non-uniform temperature distribution that leads to residual stresses and different deviations, especially buckling distortions in thin plates. In order to control the deviations and increase the quality of welded plates, a fixture can be used as a practical and low cost method with high efficiency. In this study, a coupled thermo-mechanical finite element model is coded in the software ANSYS to simulate the behavior of thin plates located by a 3-2-1 positioning system during the welding process. Computational results are compared with recent similar works to validate the finite element models. The agreement between the result of proposed model and other reported data proves that finite element modeling can accurately predict the behavior of welded thin plates.
Digital Article Identifier (DAI):
125
10935
Sequential Straightforward Clustering for Local Image Block Matching
Abstract: Duplicated region detection is a technical method to
expose copy-paste forgeries on digital images. Copy-paste is one
of the common types of forgeries to clone portion of an image
in order to conceal or duplicate special object. In this type of
forgery detection, extracting robust block feature and also high
time complexity of matching step are two main open problems.
This paper concentrates on computational time and proposes a local
block matching algorithm based on block clustering to enhance time
complexity. Time complexity of the proposed algorithm is formulated
and effects of two parameter, block size and number of cluster, on
efficiency of this algorithm are considered. The experimental results
and mathematical analysis demonstrate this algorithm is more costeffective
than lexicographically algorithms in time complexity issue
when the image is complex.
Digital Article Identifier (DAI):
124
3032
Goal-Based Request Cloud Resource Broker in Medical Application
Abstract: In this paper, cloud resource broker using goalbased
request in medical application is proposed. To handle recent
huge production of digital images and data in medical informatics
application, the cloud resource broker could be used by medical
practitioner for proper process in discovering and selecting correct
information and application. This paper summarizes several
reviewed articles to relate medical informatics application with
current broker technology and presents a research work in applying
goal-based request in cloud resource broker to optimize the use of
resources in cloud environment. The objective of proposing a new
kind of resource broker is to enhance the current resource
scheduling, discovery, and selection procedures. We believed that
it could help to maximize resources allocation in medical
informatics application.
Digital Article Identifier (DAI):
123
595
The Sequestration of Heavy Metals Contaminating the Wonderfonteinspruit Catchment Area using Natural Zeolite
Abstract: For more than 120 years, gold mining formed the
backbone the South Africa-s economy. The consequence of mine
closure was observed in large-scale land degradation and widespread
pollution of surface water and groundwater. This paper investigates
the feasibility of using natural zeolite in removing heavy metals
contaminating the Wonderfonteinspruit Catchment Area (WCA), a
water stream with high levels of heavy metals and radionuclide
pollution. Batch experiments were conducted to study the adsorption
behavior of natural zeolite with respect to Fe2+, Mn2+, Ni2+, and Zn2+.
The data was analysed using the Langmuir and Freudlich isotherms.
Langmuir was found to correlate the adsorption of Fe2+, Mn2+, Ni2+,
and Zn2+ better, with the adsorption capacity of 11.9 mg/g, 1.2 mg/g,
1.3 mg/g, and 14.7 mg/g, respectively. Two kinetic models namely,
pseudo-first order and pseudo second order were also tested to fit the
data. Pseudo-second order equation was found to be the best fit for
the adsorption of heavy metals by natural zeolite. Zeolite
functionalization with humic acid increased its uptake ability.
Digital Article Identifier (DAI):
122
7164
Estimating the Absorption of Volatile Organic Compounds in Four Biodiesels Using the UNIFAC Procedure
Abstract: This work considered the thermodynamic feasibility
of scrubbing volatile organic compounds into biodiesel in view of
designing a gas treatment process with this absorbent. A detailed
vapour – liquid equilibrium investigation was performed using the
original UNIFAC group contribution method. The four biodiesels
studied in this work are methyl oleate, methyl palmitate, methyl
linolenate and ethyl stearate. The original UNIFAC procedure was
used to estimate the infinite dilution activity coefficients of 13
selected volatile organic compounds in the biodiesels. The
calculations were done at the VOC mole fraction of 9.213x10-8. Ethyl
stearate gave the most favourable phase equilibrium. A close
agreement was found between the infinite dilution activity coefficient
of toluene found in this work and those reported in literature.
Thermodynamic models can efficiently be used to calculate vast
amount of phase equilibrium behaviour using limited number of
experimental data.
Digital Article Identifier (DAI):
121
14927
Absorption of Volatile Organic Compounds into Polydimethylsiloxane: Phase Equilibrium Computation at Infinite Dilution
Abstract: Group contribution methods such as the UNIFAC are
very useful to researchers and engineers involved in synthesis,
feasibility studies, design and optimization of separation processes.
They can be applied successfully to predict phase equilibrium and
excess properties in the development of chemical and separation
processes. The main focus of this work was to investigate the
possibility of absorbing selected volatile organic compounds (VOCs)
into polydimethylsiloxane (PDMS) using three selected UNIFAC
group contribution methods. Absorption followed by subsequent
stripping is the predominant available abatement technology of
VOCs from flue gases prior to their release into the atmosphere. The
original, modified and effective UNIFAC models were used in this
work. The thirteen selected VOCs that have been considered in this
research are: pentane, hexane, heptanes, trimethylamine, toluene,
xylene, cyclohexane, butyl acetate, diethyl acetate, chloroform,
acetone, ethyl methyl ketone and isobutyl methyl ketone. The
computation was done for solute VOC concentration of 8.55x10-8
which is well in the infinite dilution region. The results obtained in
this study compare very well with those published in literature
obtained through both measurements and predictions. The phase
equilibrium obtained in this study show that PDMS is a good
absorbent for the removal of VOCs from contaminated air streams
through physical absorption.
Digital Article Identifier (DAI):
120
5099
Effectiveness and Usability Evaluation of 'Li2D' Courseware
Abstract: Multimedia courseware has been accepted as a tool
that can support teaching and learning process. 'Li2D' courseware
was developed to assist student-s visualization on the topic of Loci in
Two Dimension. This paper describes an evaluation on the
effectiveness and usability of a 'Li2D' courseware. The quasi
experiment was used for the effectiveness evaluation. Usability
evaluation was accomplished based on four constructs of usability,
namely: efficiency, learnability, screen design and satisfaction. An
evaluation on the multimedia elements was also conducted. A total of
63 students of Form Two are involved in the study. The students are
divided into two groups: control and experimental. The experimental
group had to interact with 'Li2D' courseware as part of the learning
activities while the control group used the conventional learning
methods. The results indicate that the experimental group performed
better than the control group in understanding the Loci in Two
Dimensions topic. In terms of usability, the results showed that the
students agreed on the usability in multimedia elements in the 'Li2D'
courseware.
Digital Article Identifier (DAI):
119
14340
Intrinsic Electromagnetic Fields and Atom-Field Coupling in Living Cells
Abstract: The possibility of intrinsic electromagnetic fields
within living cells and their resonant self-interaction and interaction
with ambient electromagnetic fields is suggested on the basis of a
theoretical and experimental study. It is reported that intrinsic
electromagnetic fields are produced in the form of radio-frequency
and infra-red photons within atoms (which may be coupled or
uncoupled) in cellular structures, such as the cell cytoskeleton and
plasma membrane. A model is presented for the interaction of these
photons among themselves or with atoms under a dipole-dipole
coupling, induced by single-photon or two-photon processes. This
resonance is manifested by conspicuous field amplification and it is
argued that it is possible for these resonant photons to undergo
tunnelling in the form of evanescent waves to a short range (of a few
nanometers to micrometres). This effect, suggested as a resonant
photon tunnelling mechanism in this report, may enable these fields
to act as intracellular signal communication devices and as bridges
between macromolecules or cellular structures in the cell
cytoskeleton, organelles or membrane. A brief overview of an
experimental technique and a review of some preliminary results are
presented, in the detection of these fields produced in living cell
membranes under physiological conditions.
Digital Article Identifier (DAI):
118
4545
Experimental Technique for Vibration Reduction of a Motor Pumpin Medical Device
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Digital Article Identifier (DAI):
117
4026
Temperature-dependent Structural Perturbation of Tuna Myoglobin
Abstract: To unveil the mechanism of fast autooxidation of fish
myoglobins, the effect of temperature on the structural change of tuna
myoglobin was investigated. Purified myoglobin was subjected to
preincubation at 5, 20, 50 and 40oC. Overall helical structural decay
through thermal treatment up to 95oC was monitored by circular
dichroism spectrometry, while the structural changes around the heme
pocket was measured by ultraviolet/visible absorption spectrophotometry.
As a result, no essential structural change of myoglobin
was observed under 30oC, roughly equivalent to their body
temperature, but the structure was clearly damaged at 40oC. The Soret
band absorption hardly differed irrespective of preincubation
temperature, suggesting that the structure around the heme pocket was
not perturbed even after thermal treatment.
Digital Article Identifier (DAI):
116
7827
Design of Novel SCR-based ESD Protection Device for I/O Clamp in BCD Process
Abstract: In this paper, a novel LVTSCR-based device for
electrostatic discharge (ESD) protection of integrated circuits (ICs) is
designed, fabricated and characterized. The proposed device is similar
to the conventional LVTSCR but it has an embedded PMOSFET in the
anode n-well to enhance the turn on speed, the clamping capability and
the robustness. This is possible because the embedded PMOSFET
provides the sub-path of ESD discharge current. The TLP, HBM and
MM testing are carried out to verify the ESD performance of the
proposed devices, which are fabricated in 0.35um
(Bipolar-CMOS-DMOS) BCDMOS process. The device has the
robustness of 70mA/um that is higher about 60mA/um than the
LVTSCR, approximately.
Digital Article Identifier (DAI):
115
467
Using Data Mining Methodology to Build the Predictive Model of Gold Passbook Price
Abstract: Gold passbook is an investing tool that is especially
suitable for investors to do small investment in the solid gold. The gold
passbook has the lower risk than other ways investing in gold, but its
price is still affected by gold price. However, there are many factors
can cause influences on gold price. Therefore, building a model to
predict the price of gold passbook can both reduce the risk of
investment and increase the benefits. This study investigates the
important factors that influence the gold passbook price, and utilize
the Group Method of Data Handling (GMDH) to build the predictive
model. This method can not only obtain the significant variables but
also perform well in prediction. Finally, the significant variables of
gold passbook price, which can be predicted by GMDH, are US dollar
exchange rate, international petroleum price, unemployment rate,
whole sale price index, rediscount rate, foreign exchange reserves,
misery index, prosperity coincident index and industrial index.
Digital Article Identifier (DAI):
114
4186
Simulation of Sloshing-Shear Mixed Shallow Water Waves (II) Numerical Solutions
Abstract: This is the second part of the paper. It, aside from the
core subroutine test reported previously, focuses on the simulation of
turbulence governed by the full STF Navier-Stokes equations on a
large scale. Law of the wall is found plausible in this study as a model
of the boundary layer dynamics. Model validations proceed to
include velocity profiles of a stationary turbulent Couette flow, pure
sloshing flow simulations, and the identification of water-surface
inclination due to fluid accelerations. Errors resulting from the
irrotational and hydrostatic assumptions are explored when studying
a wind-driven water circulation with no shakings. Illustrative
examples show that this numerical strategy works for the simulation
of sloshing-shear mixed flow in a 3-D rigid rectangular base tank.
Digital Article Identifier (DAI):
113
4698
Polyethylenimine Coated Carbon Nanotube for Detecting Rancidity in Frying Oil
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Digital Article Identifier (DAI):
112
10211
Economic Returns of Using Brewery`s Spent Grain in Animal Feed
Abstract: UK breweries generate extensive by products in the
form of spent grain, slurry and yeast. Much of the spent grain is
produced by large breweries and processed in bulk for animal feed.
Spent brewery grains contain up to 20% protein dry weight and up to
60% fiber and are useful additions to animal feed. Bulk processing is
economic and allows spent grain to be sold so providing an income
to the brewery. A proportion of spent grain, however, is produced by
small local breweries and is more variably distributed to farms or
other users using intermittent collection methods. Such use is much
less economic and may incur losses if not carefully assessed for
transport costs. This study reports an economic returns of using wet
brewery spent grain (WBSG) in animal feed using the Co-product
Optimizer Decision Evaluator model (Cattle CODE) developed by
the University of Nebraska to predict performance and economic
returns when byproducts are fed to finishing cattle. The results
indicated that distance from brewery to farm had a significantly
greater effect on the economics of use of small brewery spent grain
and that alternative uses than cattle feed may be important to
develop.
Digital Article Identifier (DAI):
111
6386
Surface Plasmon Polariton Excitation by a Phase Shift Grating
Abstract: We focus on the excitation and propagation properties
of surface plasmon polariton (SPP). We have developed a SPP
excitation device in combination with a grating structures fabricated
by using the scanning probe lithography. Perturbation approach was
used to investigate the coupling properties of SPP with a spatial
harmonic wave supported by a metallic grating. A phase shift grating
SPP coupler has been fabricated and the optical property was
evaluated by the Fraunhofer diffraction formula. We have been
experimentally confirmed the induced stop band by diffraction
measurement. We have also observed the wavenumber shift of the
resonance condition of SPP owing to effect of a phase shift.
Digital Article Identifier (DAI):
110
6345
The Effects of Sodium Chloride in the Formation of Size and Shape of Gold (Au)Nanoparticles by Microwave-Polyol Method for Mercury Adsorption
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Digital Article Identifier (DAI):
109
10556
Reutilization of Organic and Peat Soils by Deep Cement Mixing
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Digital Article Identifier (DAI):
108
15076
Multi-Agent Model for Automation of Business Process Management System Based on Service Oriented Architecture
Abstract: Business process automation is an important task in an
enterprise business environment software development. The
requirements of processing acceleration and automation level of
enterprises are inherently different from one organization to another.
We present a methodology and system for automation of business
process management system architecture by multi-agent collaboration
based on SOA. Design layer processes are modeled in semantic
markup language for web services application. At the core of our
system is considering certain types of human tasks to their further
automation across over multiple platform environments. An
improved abnormality processing with model for automation of
BPMS architecture by multi-agent collaboration based on SOA is
introduced. Validating system for efficiency of process automation,
an application for educational knowledge base instance would also be
described.
Digital Article Identifier (DAI):
107
4116
Performance of Compound Enhancement Algorithms on Dental Radiograph Images
Abstract: The purpose of this research is to compare the original
intra-oral digital dental radiograph images with images that are
enhanced using a combination of image processing algorithms. Intraoral
digital dental radiograph images are often noisy, blur edges and
low in contrast. A combination of sharpening and enhancement
method are used to overcome these problems. Three types of
proposed compound algorithms used are Sharp Adaptive Histogram
Equalization (SAHE), Sharp Median Adaptive Histogram
Equalization (SMAHE) and Sharp Contrast adaptive histogram
equalization (SCLAHE). This paper presents an initial study of the
perception of six dentists on the details of abnormal pathologies and
improvement of image quality in ten intra-oral radiographs. The
research focus on the detection of only three types of pathology
which is periapical radiolucency, widen periodontal ligament space
and loss of lamina dura. The overall result shows that SCLAHE-s
slightly improve the appearance of dental abnormalities- over the
original image and also outperform the other two proposed
compound algorithms.
Digital Article Identifier (DAI):
106
1291
Mining Implicit Knowledge to Predict Political Risk by Providing Novel Framework with Using Bayesian Network
Abstract: Nowadays predicting political risk level of country
has become a critical issue for investors who intend to achieve
accurate information concerning stability of the business
environments. Since, most of the times investors are layman and
nonprofessional IT personnel; this paper aims to propose a
framework named GECR in order to help nonexpert persons to
discover political risk stability across time based on the political
news and events.
To achieve this goal, the Bayesian Networks approach was
utilized for 186 political news of Pakistan as sample dataset.
Bayesian Networks as an artificial intelligence approach has been
employed in presented framework, since this is a powerful technique
that can be applied to model uncertain domains. The results showed
that our framework along with Bayesian Networks as decision
support tool, predicted the political risk level with a high degree of
accuracy.
Digital Article Identifier (DAI):
105
6055
Further Investigation of Elastic Scattering of 16O on 12C at Different Energies
Abstract: The aim of this work is to study the elastic transfer
phenomenon which takes place in the elastic scattering of 16O on 12C
at energies near the Coulomb barrier. Where, the angular distribution
decrease steadily with increasing the scattering angle, then the cross
section will increase at backward angles due to the α-transfer process.
This reaction was also studied at different energies for tracking the
nuclear rainbow phenomenon. The experimental data of the angular
distribution at these energies were compared to the calculation
predictions. The optical potential codes such as SPIVAL and
Distorted Wave Born Approximation (DWUCK5) were used in
analysis.
Digital Article Identifier (DAI):
104
12540
Germination of Barley as Affected by the Allelopathy of Sisymbrium irio L. and Descurainiasophia (L.) Schur
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of barley. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The results showed that the SISIR water extracts had a greater
inhibitory effects on the germination and primary growth of barley
than those of DESSO water extracts. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on the
germination and primary growth of barley, compared to those of
stems and roots. Increasing the concentration of water extracts of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to barley and reduced the germination rate and
primary growth of it linearly.
Digital Article Identifier (DAI):
103
1378
Detailed Phenomenological Study of 14N Elastically Scattered on 12C in a wide Energy Range
Abstract: An experiment was performed with a 24.5 MeV 14N
beam on a 12C target in the cyclotron DC-60 located in Astana,
Kazakhstan, to study the elastic scattering of 14N on 12C; the
scattering was also analyzed at different energies for tracking the
phenomenon of remarkable structure at large angles. Its aims were to
extend the measurements to very large angles, and attempt to
uniquely identify the elastic scattering potential. Good agreement
between the theoretical and experimental data has been obtained with
suitable optical potential parameters. Optical model calculations with
l -dependent imaginary potentials were also applied to the data and
relatively good agreement was found.
Digital Article Identifier (DAI):
102
8167
Allelopathic Effects of Sisymbrium irio L. and Descurainia sophia (L.) Schur on the Germination of Wheat (Triticum aestivum L.)
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and/or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of wheat. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The plant materials were cut in 2-3 cm pieces and then were
ground in a blender. The crushed materials were weighed
according to experimental protocol and the final volume was
reached to 100 ml in distilled water in dark bottles. All bottles were
put on a shaker for 24 hours. The solutions were filtered by muslin
cloth. Whatman paper, 9 cm in diameter, were put in petri dishes
and twenty seeds of wheat were put on it and 5 ml distilled water
or water extract of weeds were added to each petri dish. All petri
dishes were put in constant temperature of 15 0C incubator.
The results showed that the SISIR water extract had a greater
inhibitory effects on germination and primary growth of wheat
than those of DESSO water extract. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on
germination and primary growth of wheat, compared to those of
stems and roots. Increasing the concentration of water extract of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to wheat and reduced the germination rate and
primary growth of it linearly.
Digital Article Identifier (DAI):
101
8965
Assessment of Sediment Quality According To Heavy Metal Status in the West Port of Malaysia
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Digital Article Identifier (DAI):
100
1068
Efficiency Enhancement of PWM Controlled Water Electrolysis Cells
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.
Digital Article Identifier (DAI):
99
15771
Numerical Calculation of the Ionization Energy of Donors in a Cubic Quantum well and Wire
Abstract: The ionization energy in semiconductor
systems in nano scale was investigated by using effective mass
approximation. By introducing the Hamiltonian of the system, the
variational technique was employed to calculate the ground state and
the ionization energy of a donor at the center and in the case that the
impurities are randomly distributed inside a cubic quantum well. The
numerical results for GaAs/GaAlAs show that the ionization energy
strongly depends on the well width for both cases and it decreases as
the well width increases. The ionization energy of a quantum wire
was also calculated and compared with the results for the well.
Digital Article Identifier (DAI):
98
11844
Modeling of Bio Scaffolds: Structural and Fluid Transport Characterization
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Digital Article Identifier (DAI):
97
12388
Bactericidal Properties of Carbohydrate-Stabilized Platinum Oxide Nanoparticles
Abstract: Platinum oxide nanoparticles were prepared by a
simple hydrothermal route and chemical reduction using
carbohydrates (Fructose and sucrose) as the reducing and
stabilizing agents. The crystallite size of these nanoparticles was
evaluated from X-ray diffraction (XRD), atomic force microscopy
(AFM) and transmission electron microscopy (TEM) and was
found to be 10 nm as shown in figure 1, which is the
demonstration of EM bright field and transmission electron
microscopy. The effect of carbohydrates on the morphology of the
nanoparticles was studied using TEM (Figure 1). The
nanoparticles (100 μg/ml) were administered to the Pseudomonas
Stutzeri and Lactobacillus cultures and the incubation was done at
35 oC for 24 hours. The nanocomposites exhibited interesting
inhibitory as well as bactericidal activity against P. Stutzeri and
and Lactobacillus species. Incorporation of nanoparticles also
increased the thermal stability of the carbohydrates.
Digital Article Identifier (DAI):
96
13895
The Buffer Gas Influence Rate on Absolute Cu Atoms Density with regard to Deposition
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Digital Article Identifier (DAI):
95
838
Meteorological Data Study and Forecasting Using Particle Swarm Optimization Algorithm
Abstract: Weather systems use enormously complex
combinations of numerical tools for study and forecasting.
Unfortunately, due to phenomena in the world climate, such
as the greenhouse effect, classical models may become
insufficient mostly because they lack adaptation. Therefore,
the weather forecast problem is matched for heuristic
approaches, such as Evolutionary Algorithms.
Experimentation with heuristic methods like Particle Swarm
Optimization (PSO) algorithm can lead to the development of
new insights or promising models that can be fine tuned with
more focused techniques. This paper describes a PSO
approach for analysis and prediction of data and provides
experimental results of the aforementioned method on realworld
meteorological time series.
Digital Article Identifier (DAI):
94
12362
Digital Forensics for Electronic Commerce on the Web
Abstract: On existing online shopping on the web, SSL and
password are usually used to achieve the secure trades. SSL shields
communication from the third party who is not related with the trade,
and indicates that the trader's web site is authenticated by one of the
certification authority. Password certifies a customer as the same
person who has visited the trader's web site before, and protects the
customer's privacy such as what the customer has bought on the site.
However, there is no forensics for the trades in those cased above.
With existing methods, no one can prove what is ordered by
customers, how many products are ordered and even whether
customers have ordered or not. The reason is that the third party has to
guess what were traded with logs that are held by traders and by
customers. The logs can easily be created, deleted and forged since
they are electronically stored. To enhance security with digital
forensics for electronic commerce on the web, I indicate a secure
method with cellular phones.
Digital Article Identifier (DAI):
93
13371
Classifying Biomedical Text Abstracts based on Hierarchical 'Concept' Structure
Abstract: Classifying biomedical literature is a difficult and
challenging task, especially when a large number of biomedical
articles should be organized into a hierarchical structure. In this paper,
we present an approach for classifying a collection of biomedical text
abstracts downloaded from Medline database with the help of
ontology alignment. To accomplish our goal, we construct two types
of hierarchies, the OHSUMED disease hierarchy and the Medline
abstract disease hierarchies from the OHSUMED dataset and the
Medline abstracts, respectively. Then, we enrich the OHSUMED
disease hierarchy before adapting it to ontology alignment process for
finding probable concepts or categories. Subsequently, we compute
the cosine similarity between the vector in probable concepts (in the
“enriched" OHSUMED disease hierarchy) and the vector in Medline
abstract disease hierarchies. Finally, we assign category to the new
Medline abstracts based on the similarity score. The results obtained
from the experiments show the performance of our proposed approach
for hierarchical classification is slightly better than the performance of
the multi-class flat classification.
Digital Article Identifier (DAI):
92
11123
Model Based Monitoring Using Integrated Data Validation, Simulation and Parameter Estimation
Abstract: Efficient and safe plant operation can only be
achieved if the operators are able to monitor all key process
parameters. Instrumentation is used to measure many process
variables, like temperatures, pressures, flow rates, compositions or
other product properties. Therefore Performance monitoring is a
suitable tool for operators. In this paper, we integrate rigorous
simulation model, data reconciliation and parameter estimation to
monitor process equipments and determine key performance
indicator (KPI) of them. The applied method here has been
implemented in two case studies.
Digital Article Identifier (DAI):
91
13705
High Optical Properties and Rectifying Behavior of ZnO (Nano and Microstructures)/Si Heterostructures
Abstract: We investigated a modified thermal evaporation
method in the growth process of ZnO nanowires. ZnO nanowires
were fabricated on p-type silicon substrates without using a metal
catalyst. A simple horizontal double-tube system along with
chemical vapor diffusion of the precursor was used to grow the ZnO
nanowires. The substrates were placed in different temperature
zones, and ZnO nanowires with different diameters were obtained for
the different substrate temperatures. In addition to the nanowires,
ZnO microdiscs with different diameters were obtained on another
substrate, which was placed at a lower temperature than the other
substrates. The optical properties and crystalline quality of the ZnO
nanowires and microdiscs were characterized by room temperature
photoluminescence (PL) and Raman spectrometers. The PL and
Raman studies demonstrated that the ZnO nanowires and microdiscs
grown using such set-up had good crystallinity with excellent optical
properties. Rectifying behavior of ZnO/Si heterostructures was
characterized by a simple DC circuit.
Digital Article Identifier (DAI):
90
14720
An Efficient Spam Mail Detection by Counter Technique
Abstract: Spam mails are unwanted mails sent to large number
of users. Spam mails not only consume the network resources, but
cause security threats as well. This paper proposes an efficient
technique to detect, and to prevent spam mail in the sender side rather
than the receiver side. This technique is based on a counter set on the
sender server. When a mail is transmitted to the server, the mail server
checks the number of the recipients based on its counter policy. The
counter policy performed by the mail server is based on some
pre-defined criteria. When the number of recipients exceeds the
counter policy, the mail server discontinues the rest of the process, and
sends a failure mail to sender of the mail; otherwise the mail is
transmitted through the network. By using this technique, the usage of
network resources such as bandwidth, and memory is preserved. The
simulation results in real network show that when the counter is set on
the sender side, the time required for spam mail detection is 100 times
faster than the time the counter is set on the receiver side, and the
network resources are preserved largely compared with other
anti-spam mail techniques in the receiver side.
Digital Article Identifier (DAI):
89
2944
Coordinated Voltage Control using Multiple Regulators in Distribution System with Distributed Generators
Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.
Digital Article Identifier (DAI):
88
15948
Study on the Effect of Volume Fraction of Dual Phase Steel to Corrosion Behaviour and Hardness
Abstract: The objective of this project is to study the corrosion
behaviour and hardness based on the presence of martensite in dual
phase steel. This study was conducted on six samples of dual phase
steel which have different percentage of martensite. A total of 9
specimens were prepared by intercritical annealing process to study
the effect of temperature to the formation of martensite. The low
carbon steels specimens were heated for 25 minutes in a specified
temperature ranging from 7250C to 8250C followed by rapid cooling
in water. The measurement of corrosion rate was done by using
extrapolation tafel method, while potentiostat was used to control and
measured the current produced. This measurement is performed
through a system named CMS105. The result shows that a specimen
with higher percentage of martensite is likely to corrode faster.
Hardness test for each specimen was conducted to compare its
hardness with low carbon steel. The results obtained indicate that the
specimen hardness is proportional to the amount of martensite in dual
phase steel.
Digital Article Identifier (DAI):
87
626
Study on Plasma Creation and Propagation in a Pulsed Magnetoplasmadynamic Thruster
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Digital Article Identifier (DAI):
86
14654
The Prevalence of Transfusion-Transmitted Virus (TTV) Infection inIranian Patients with Chronic Hepatitis B
Abstract: TTV is an unenveloped circular single-stranded DNA
virus with a diameter of 30-32 nm that first was described in 1997 in
Japan. TTV was detected in various populations without proven
pathology, including blood donors and in patients with chronic HBV
and HCV hepatitis. The aim of this study was to determine the
prevalence of TTV DNA in Iranian patients with chronic hepatitis B
and C. Viral TTV-DNA was studied in 442 samples (202 with HBV,
138 with HCV and 102 controls) collected from west south of Iran.
All extracted serum DNA was amplified by TTV ORF1 gene specific
primers using the semi nested PCR technique. TTV DNA was
detected in the serum of 8.9% and 10.8% patients with chronic
hepatitis B and C, respectively. Prevalence of TTV-DNA in the serum
of 102 controls was 2.9%. Results showed significant relation of TTV
with HBV and HCV in patients by using T test examination (P
Digital Article Identifier (DAI):
85
2812
Tool Failure Detection Based on Statistical Analysis of Metal Cutting Acoustic Emission Signals
Abstract: The analysis of Acoustic Emission (AE) signal
generated from metal cutting processes has often approached
statistically. This is due to the stochastic nature of the emission
signal as a result of factors effecting the signal from its generation
through transmission and sensing. Different techniques are applied in
this manner, each of which is suitable for certain processes. In metal
cutting where the emission generated by the deformation process is
rather continuous, an appropriate method for analysing the AE signal
based on the root mean square (RMS) of the signal is often used and
is suitable for use with the conventional signal processing systems.
The aim of this paper is to set a strategy in tool failure detection in
turning processes via the statistic analysis of the AE generated from
the cutting zone. The strategy is based on the investigation of the
distribution moments of the AE signal at predetermined sampling.
The skews and kurtosis of these distributions are the key elements in
the detection. A normal (Gaussian) distribution has first been
suggested then this was eliminated due to insufficiency. The so
called Beta distribution was then considered, this has been used with
an assumed β density function and has given promising results with
regard to chipping and tool breakage detection.
Digital Article Identifier (DAI):
84
6306
Study of the Elastic Scattering of 16O, 14N and 12C on the Nucleus of 27Al at Different Energies near the Coulomb Barrier
Abstract: the measurement of the angular distribution for the
elastic scattering of 16O, 14N and 12C on 27Al has been done at energy
1.75 MeV/nucleon. The optical potential code SPIVAL used in this
work to analyze the experimental results. A good agreement between
the experimental and theoretical results was obtained.
Digital Article Identifier (DAI):
83
93
Curing Methods Yield Multiple Refractive Index of Benzocyclobutene Polymer Film
Abstract: Refractive index control of benzocyclobutene (BCB 4024-40) is achieved by facilitating different conditions during the thermal curing of BCB film. Refractive index (RI) change of 1.49% is obtained with curing of BCB film using an oven, while the RI change is 0.1% when the BCB is cured using a hotplate. The two different curing methods exhibit a temperature dependent refractive index change of the BCB photosensitive polymer. By carefully controlling the curing conditions, multiple layers of BCB with different RI can be fabricated, which can then be applied in the fabrication of optical waveguides.
Digital Article Identifier (DAI):
82
12542
Efficient Feature-Based Registration for CT-M R Images Based on NSCT and PSO
Abstract: Feature-based registration is an effective technique for clinical use, because it can greatly reduce computational costs. However, this technique, which estimates the transformation by using feature points extracted from two images, may cause misalignments. To handle with this limitation, we propose to extract the salient edges and extracted control points (CP) of medical images by using efficiency of multiresolution representation of data nonsubsampled contourlet transform (NSCT) that finds the best feature points. The MR images were first decomposed using the NSCT, and then Edge and CP were extracted from bandpass directional subband of NSCT coefficients and some proposed rules. After edge and CP extraction, mutual information was adopted for the registration of feature points and translation parameters are calculated by using particle swarm optimization (PSO). The experimental results showed that the proposed method produces totally accurate performance for registration medical CT-MR images.
Digital Article Identifier (DAI):
81
11381
Carbothermic Reduction of Mechanically Activated Mixtures of Celestite and Carbon
Abstract: The effect of dry milling on the carbothermic
reduction of celestite was investigated. Mixtures of celestite
concentrate (98% SrSO4) and activated carbon (99% carbon) was
milled for 1 and 24 hours in a planetary ball mill. Un-milled and
milled mixtures and their products after carbothermic reduction were
studied by a combination of XRD and TGA/DTA experiments. The
thermogravimetric analyses and XRD results showed that by milling
celestite-carbon mixtures for one hour, the formation temperature of
strontium sulfide decreased from about 720°C (in un-milled sample)
to about 600°C, after 24 hours milling it decreased to 530°C. It was
concluded that milling induces increasingly thorough mixing of the
reactants to reduction occurring at lower temperatures
Digital Article Identifier (DAI):
80
13581
Optimizing Voltage Parameter of Deep Brain Stimulation for Parkinsonian Patients by Modeling
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Digital Article Identifier (DAI):
79
2965
Studding of Number of Dataset on Precision of Estimated Saturated Hydraulic Conductivity
Abstract: Saturated hydraulic conductivity of Soil is an
important property in processes involving water and solute flow in
soils. Saturated hydraulic conductivity of soil is difficult to measure
and can be highly variable, requiring a large number of replicate
samples. In this study, 60 sets of soil samples were collected at
Saqhez region of Kurdistan province-IRAN. The statistics such as
Correlation Coefficient (R), Root Mean Square Error (RMSE), Mean
Bias Error (MBE) and Mean Absolute Error (MAE) were used to
evaluation the multiple linear regression models varied with number
of dataset. In this study the multiple linear regression models were
evaluated when only percentage of sand, silt, and clay content (SSC)
were used as inputs, and when SSC and bulk density, Bd, (SSC+Bd)
were used as inputs. The R, RMSE, MBE and MAE values of the 50
dataset for method (SSC), were calculated 0.925, 15.29, -1.03 and
12.51 and for method (SSC+Bd), were calculated 0.927, 15.28,-1.11
and 12.92, respectively, for relationship obtained from multiple
linear regressions on data. Also the R, RMSE, MBE and MAE values
of the 10 dataset for method (SSC), were calculated 0.725, 19.62, -
9.87 and 18.91 and for method (SSC+Bd), were calculated 0.618,
24.69, -17.37 and 22.16, respectively, which shows when number of
dataset increase, precision of estimated saturated hydraulic
conductivity, increases.
Digital Article Identifier (DAI):
78
7306
A Remote Sensing Approach for Vulnerability and Environmental Change in Apodi Valley Region, Northeast Brazil
Abstract: The objective of this study was to improve our
understanding of vulnerability and environmental change; it's causes
basically show the intensity, its distribution and human-environment
effect on the ecosystem in the Apodi Valley Region, This paper is
identify, assess and classify vulnerability and environmental change
in the Apodi valley region using a combined approach of landscape
pattern and ecosystem sensitivity. Models were developed using the
following five thematic layers: Geology, geomorphology, soil,
vegetation and land use/cover, by means of a Geographical
Information Systems (GIS)-based on hydro-geophysical parameters.
In spite of the data problems and shortcomings, using ESRI-s ArcGIS
9.3 program, the vulnerability score, to classify, weight and combine
a number of 15 separate land cover classes to create a single indicator
provides a reliable measure of differences (6 classes) among regions
and communities that are exposed to similar ranges of hazards.
Indeed, the ongoing and active development of vulnerability
concepts and methods have already produced some tools to help
overcome common issues, such as acting in a context of high
uncertainties, taking into account the dynamics and spatial scale of
asocial-ecological system, or gathering viewpoints from different
sciences to combine human and impact-based approaches. Based on
this assessment, this paper proposes concrete perspectives and
possibilities to benefit from existing commonalities in the
construction and application of assessment tools.
Digital Article Identifier (DAI):
77
8143
Stego Machine – Video Steganography using Modified LSB Algorithm
Abstract: Computer technology and the Internet have made a
breakthrough in the existence of data communication. This has
opened a whole new way of implementing steganography to ensure
secure data transfer. Steganography is the fine art of hiding the
information. Hiding the message in the carrier file enables the
deniability of the existence of any message at all. This paper designs
a stego machine to develop a steganographic application to hide data
containing text in a computer video file and to retrieve the hidden
information. This can be designed by embedding text file in a video
file in such away that the video does not loose its functionality using
Least Significant Bit (LSB) modification method. This method
applies imperceptible modifications. This proposed method strives
for high security to an eavesdropper-s inability to detect hidden
information.
Digital Article Identifier (DAI):
76
10589
Behavior Model Mapping and Transformation using Model-Driven Architecture
Abstract: Model mapping and transformation are important processes in high level system abstractions, and form the cornerstone of model-driven architecture (MDA) techniques. Considerable research in this field has devoted attention to static system abstraction, despite the fact that most systems are dynamic with high frequency changes in behavior. In this paper we provide an overview of work that has been done with regard to behavior model mapping and transformation, based on: (1) the completeness of the platform independent model (PIM); (2) semantics of behavioral models; (3) languages supporting behavior model transformation processes; and (4) an evaluation of model composition to effect the best approach to describing large systems with high complexity.
Digital Article Identifier (DAI):
75
15578
Monte Carlo Simulation of Copolymer Heterogeneity in Atom Transfer Radical Copolymerization of Styrene and N-Butyl Acrylate
Abstract: A high-performance Monte Carlo simulation, which
simultaneously takes diffusion-controlled and chain-length-dependent
bimolecular termination reactions into account, is developed to
simulate atom transfer radical copolymerization of styrene and nbutyl
acrylate. As expected, increasing initial feed fraction of styrene
raises the fraction of styrene-styrene dyads (fAA) and reduces that of
n-butyl acrylate dyads (fBB). The trend of variation in randomness
parameter (fAB) during the copolymerization also varies significantly.
Also, there is a drift in copolymer heterogeneity and the highest drift
occurs in the initial feeds containing lower percentages of styrene, i.e.
20% and 5%.
Digital Article Identifier (DAI):
74
6159
Behavior of Generated Gas in Lost Foam Casting
Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Digital Article Identifier (DAI):
73
7696
Evaluation of Groundwater Unit Hydrograph of Kavar-Maharloo Aquifer
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Kavar-
Maharloo plains in Fars plain were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 17 meters during
1995 to 2006. The purpose of this study is to evaluate water level
changes in the Kavar-Maharloo Aquifer in the Fars province in order
to determine the areas of greatest depletion, the cause of depletion,
and predict the remaining life of the aquifer.
Digital Article Identifier (DAI):
72
10295
Hair Mechanical Properties Depending on Age and Origin
Abstract: Hair is a non homogenous complex material which
can be associated with a polymer. It is made up 95% of Keratin.
Hair has a great social significance for human beings. In the High
Middle Ages, for example, long hairs have been reserved for kings
and nobles.
Most common interest in hair is focused on hair growth, hair types
and hair care, but hair is also an important biomaterial which can
vary depending on ethnic origin or on age, hair colour for example
can be a sign of ethnic ancestry or age (dark hair for Asiatic, blond
hair for Caucasian and white hair for old people in general).
In this context, different approaches have been conducted to
determine the differences in mechanical properties and characterize
the fracture topography at the surface of hair depending on its type
and its age.
A tensile testing machine was especially designed to achieve
tensile tests on hair. This device is composed of a microdisplacement
system and a force sensor whose peak load is limited to
3N. The curves and the values extracted from each experiment, allow
us to compare the evolution of the mechanical properties from one
hair to another.
Observations with a Scanning Electron Microscope (SEM) and
with an interferometer were made on different hairs. Thus, it is
possible to access the cuticle state and the fracture topography for
each category.
Digital Article Identifier (DAI):
71
5554
A Predictive control based on Neural Network for Proton Exchange Membrane Fuel Cell
Abstract: The Proton Exchange Membrane Fuel Cell (PEMFC)
control system has an important effect on operation of cell.
Traditional controllers couldn-t lead to acceptable responses because
of time- change, long- hysteresis, uncertainty, strong- coupling and
nonlinear characteristics of PEMFCs, so an intelligent or adaptive
controller is needed. In this paper a neural network predictive
controller have been designed to control the voltage of at the
presence of fluctuations of temperature. The results of
implementation of this designed NN Predictive controller on a
dynamic electrochemical model of a small size 5 KW, PEM fuel cell
have been simulated by MATLAB/SIMULINK.
Digital Article Identifier (DAI):
70
13430
Applying Case-Based Reasoning in Supporting Strategy Decisions
Abstract: Globalization and therefore increasing tight competition among companies, have resulted to increase the importance of making well-timed decision. Devising and employing effective strategies, that are flexible and adaptive to changing market, stand a greater chance of being effective in the long-term. In other side, a clear focus on managing the entire product lifecycle has emerged as critical areas for investment. Therefore, applying wellorganized tools to employ past experience in new case, helps to make proper and managerial decisions. Case based reasoning (CBR) is based on a means of solving a new problem by using or adapting solutions to old problems. In this paper, an adapted CBR model with k-nearest neighbor (K-NN) is employed to provide suggestions for better decision making which are adopted for a given product in the middle of life phase. The set of solutions are weighted by CBR in the principle of group decision making. Wrapper approach of genetic algorithm is employed to generate optimal feature subsets. The dataset of the department store, including various products which are collected among two years, have been used. K-fold approach is used to evaluate the classification accuracy rate. Empirical results are compared with classical case based reasoning algorithm which has no special process for feature selection, CBR-PCA algorithm based on filter approach feature selection, and Artificial Neural Network. The results indicate that the predictive performance of the model, compare with two CBR algorithms, in specific case is more effective.
Digital Article Identifier (DAI):
69
13572
A Context-Aware based Authorization System for Pervasive Grid Computing
Abstract: This paper describes the authorization system
architecture for Pervasive Grid environment. It discusses the
characteristics of classical authorization system and requirements of
the authorization system in pervasive grid environment as well.
Based on our analysis of current systems and taking into account the
main requirements of such pervasive environment, we propose new
authorization system architecture as an extension of the existing grid
authorization mechanisms. This architecture not only supports user
attributes but also context attributes which act as a key concept for
context-awareness thought. The architecture allows authorization of
users dynamically when there are changes in the pervasive grid
environment. For this, we opt for hybrid authorization method that
integrates push and pull mechanisms to combine the existing grid
authorization attributes with dynamic context assertions. We will
investigate the proposed architecture using a real testing environment
that includes heterogeneous pervasive grid infrastructures mapped
over multiple virtual organizations. Various scenarios are described
in the last section of the article to strengthen the proposed mechanism
with different facilities for the authorization procedure.
Digital Article Identifier (DAI):
68
4129
Time and Distance Dependence of Protons Energy Loss for Laser (pw-ps) Fusion Driven Ion Acceleration
Abstract: The anomalous generation of plasma blocks by
interaction of petawatt-picosecond laser pulses permits side-on
ignition of uncompressed solid fusion fuel following an improved
application of the hydrodynamic Chu-model for deuterium-tritium.
The new possibility of side-on laser ignition depends on accelerated
ions and produced ions beams of high energy particles by the
nonlinear ponderomotive force of the laser pulse in the plasma block,
a re-evaluation of the early hydrodynamic analysis for ignition of
inertial fusion by including inhibition factor, collective effect of
stopping power of alpha particles and the energy loss rate
reabsorption to plasma by the protons of plasma blocks being
reduced by about a factor 40.
Digital Article Identifier (DAI):
67
1390
Kinetic Modeling of the Fischer-Tropsch Reactions and Modeling Steady State Heterogeneous Reactor
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Digital Article Identifier (DAI):
66
1540
Knowledge Management Model for Managing Knowledge among Related Organizations
Abstract: Transferring information developed by other peoples is an ordinary event that happens during daily conversations, for example when employees sea each other in the organization, or when they are having lunch together, or attending a meeting, they use to talk about their experience, and discuss about their current projects, and talk about their successes over some specific problems. Despite the potential value of leveraging organizational memory and expertise by using OMS and ER, still small organizations haven-t been able to capitalize on its promised value. Each organization has its internal knowledge management system, in some of organizations the system face the lack of expert people to save their experience in the repository and in another hand on some other organizations there are lots of expert people but the organization doesn-t have the maximum use of their knowledge.
Digital Article Identifier (DAI):
65
2838
Preliminary Results of In-Vitro Skin Tissue Soldering using Gold Nanoshells and ICG Combination
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Digital Article Identifier (DAI):
64
13262
Design and Simulation of Electromagnetic Flow Meter for Circular Pipe Type
Abstract: Electromagnetic flow meter by measuring the varying of magnetic flux, which is related to the velocity of conductive flow, can measure the rate of fluids very carefully and precisely. Electromagnetic flow meter operation is based on famous Faraday's second Law. In these equipments, the constant magnetostatic field is produced by electromagnet (winding around the tube) outside of pipe and inducting voltage that is due to conductive liquid flow is measured by electrodes located on two end side of the pipe wall. In this research, we consider to 2-dimensional mathematical model that can be solved by numerical finite difference (FD) solution approach to calculate induction potential between electrodes. The fundamental concept to design the electromagnetic flow meter, exciting winding and simulations are come out by using MATLAB and PDE-Tool software. In the last stage, simulations results will be shown for improvement and accuracy of technical provision.
Digital Article Identifier (DAI):
63
2033
Methanol Concentration Sensitive SWCNT/Nafion Composites
Abstract: An aqueous methanol sensor for use in direct
methanol fuel cells (DMFCs) applications is demonstrated; the
methanol sensor is built using dispersed single-walled carbon
nanotubes (SWCNTs) with Nafion117 solution to detect the methanol
concentration in water. The study is aimed at the potential use of the
carbon nanotubes array as a methanol sensor for direct methanol fuel
cells (DMFCs). The concentration of methanol in the fuel circulation
loop of a DMFC system is an important operating parameter, because
it determines the electrical performance and efficiency of the fuel cell
system. The sensor is also operative even at ambient temperatures
and responds quickly to changes in the concentration levels of the
methanol. Such a sensor can be easily incorporated into the methanol
fuel solution flow loop in the DMFC system.
Digital Article Identifier (DAI):
62
7309
Study of Effect of Removal of Shiftrows and Mixcolumns Stages of AES and AES-KDS on their Encryption Quality and Hence Security
Abstract: This paper demonstrates the results when either
Shiftrows stage or Mixcolumns stage and when both the stages are
omitted in the well known block cipher Advanced Encryption
Standard(AES) and its modified version AES with Key Dependent
S-box(AES-KDS), using avalanche criterion and other tests namely
encryption quality, correlation coefficient, histogram analysis and
key sensitivity tests.
Digital Article Identifier (DAI):
61
15725
Design and Implementation of a Microcontroller Based LCD Screen Digital Stop Watch
Abstract: The stop watch is used to measure the time required
for a certain event. This is different from normal clocks in many
ways, one of which is the accuracy of time. The stop watch requires
much more accuracy than the normal clocks. In this paper, an
ATmega8535 microcontroller was used to control the stop watch, by
which perfect accuracy can be ensured. For compiling the C code and
for loading the compiled .hex file into the microcontroller, AVR
studio and PonyProg were used respectively. The stop watch is also
different from traditional stop watches, as it contains two different
timing modes namely 'Split timing' and 'Lap timing'.
Digital Article Identifier (DAI):
60
9189
A Dynamic Filter for Removal DC - Offset In Current and Voltage Waveforms
Abstract: In power systems, protective relays must filter their
inputs to remove undesirable quantities and retain signal quantities of
interest. This job must be performed accurate and fast. A new
method for filtering the undesirable components such as DC and
harmonic components associated with the fundamental system
signals. The method is s based on a dynamic filtering algorithm. The
filtering algorithm has many advantages over some other classical
methods. It can be used as dynamic on-line filter without the need of
parameters readjusting as in the case of classic filters. The proposed
filter is tested using different signals. Effects of number of samples
and sampling window size are discussed. Results obtained are
presented and discussed to show the algorithm capabilities.
Digital Article Identifier (DAI):
59
6383
SWNT Sensors for Monitoring the Oxidation of Edible Oils
Abstract: There are several means to measure the oxidation of edible oils, such as the acid value, the peroxide value, and the anisidine value. However, these means require large quantities of reagents and are time-consuming tasks. Therefore, a more convenient and time-saving way to measure the oxidation of edible oils is required. In this report, an edible oil condition sensor was fabricated by using single-walled nanotubes (SWNT). In order to test the sensor, oxidized edible oils, each one at a different acid value, were prepared. The SWNT sensors were immersed into these oxidized oils and the resistance changes in the sensors were measured. It was found that the conductivity of the sensors decreased as the oxidation level of oil increased. This result suggests that a change of the oil components induced by the oxidation process in edible oils is related to the conductivity change in the SWNT sensor.
Digital Article Identifier (DAI):
58
2824
Photoluminescence Properties of β-FeSi2 on Cu- or Au-coated Si
Abstract: The photoluminescence (PL) at 1.55 μm from
semiconducting β-FeSi2 has attracted a noticeable interest for
silicon-based optoelectronic applications. Moreover, its high optical
absorption coefficient (higher than 105 cm-1 above 1.0 eV) allows this
semiconducting material to be used as photovoltanics devices.
A clear PL spectrum for β-FeSi2 was observed by Cu or Au coating
on Si(001). High-crystal-quality β-FeSi2 with a low-level nonradiative
center was formed on a Cu- or Au- reated Si layer. This method of
deposition can be applied to other materials requiring high crystal
quality.
Digital Article Identifier (DAI):
57
14988
Differentiation Capacity of Mouse L929 Fibroblastic Cell Line Compare With Human Dermal Fibroblast
Abstract: Mouse L929 fibroblastic cell line, which is widely
used in many experiment aspects, was tested for their differentiation
potency in osteogenic differentiation and adipogenic differentiation.
Human dermal fibroblasts, which their differentiation potency are
still be in confliction, also be taken in the experiment. The
differentiations were conducted by using the inducing medium
ingredients which is generally used to induce differentiation of stem
cells. By the inducing media used, L929 mouse fibroblasts
successfully underwent osteogenic differentiation and adipogenic
differentiation while human dermal fibroblasts underwent only
osteogenic differentiation but not for adipogenic differentiation.
Human dermal fibroblasts are hard to be differentiated in adipogenic
lineage and need specific proper condition for induction.
Digital Article Identifier (DAI):
56
12897
Optimization Approach on Flapping Aerodynamic Characteristics of Corrugated Airfoil
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Digital Article Identifier (DAI):
55
7558
Energy-Efficient Electrical Power Distribution with Multi-Agent Control at Parallel DC/DC Converters
Abstract: Consumer electronics are pervasive. It is impossible to
imagine a household or office without DVD players, digital cameras,
printers, mobile phones, shavers, electrical toothbrushes, etc. All
these devices operate at different voltage levels ranging from 1.8 to
20 VDC, in the absence of universal standards. The voltages
available are however usually 120/230 VAC at 50/60 Hz. This
situation makes an individual electrical energy conversion system
necessary for each device. Such converters usually involve several
conversion stages and often operate with excessive losses and poor
reliability. The aim of the project presented in this paper is to design
and implement a multi-channel DC/DC converter system,
customizing the output voltage and current ratings according to the
requirements of the load. Distributed, multi-agent techniques will be
applied for the control of the DC/DC converters.
Digital Article Identifier (DAI):
54
10210
The Effects of Human Activity in Yasuj Area on the Health of Stream City
Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Digital Article Identifier (DAI):
53
4146
Curriculum and Sex-specific Differences in Academic Stress Arising from Perceived Expectations
Abstract: With the aim of knowing whether curriculum and sex
differences exist in academic stress arising from perceived
expectations, high school students were asked to respond to the
Academic Expectations Stress Inventory (AESI). AESI is a nine-item
inventory with two domains, namely: expectations of
teachers/parents and expectations of self. Out of the 504 officially
enrolled high school students in a state college, 469 responded to the
inventory. Responses were analyzed using independent samples ttest.
Significant differences were found between the mean scores of
the respondents coming from the Science and the Vocational
curriculum. The respondents from the Science curriculum
consistently registered higher mean scores. Likewise, significant
differences were found between the male and the female respondents.
The female respondents consistently registered higher mean scores.
Digital Article Identifier (DAI):
52
12590
An Optimization of the New Die Design of Sheet Hydroforming by Taguchi Method
Abstract: During the last few years, several sheet hydroforming
processes have been introduced. Despite the advantages of these
methods, they have some limitations. Of the processes, the two main
ones are the standard hydroforming and hydromechanical deep
drawing. A new sheet hydroforming die set was proposed that has the
advantages of both processes and eliminates their limitations. In this
method, a polyurethane plate was used as a part of the die-set to
control the blank holder force. This paper outlines the Taguchi
optimization methodology, which is applied to optimize the effective
parameters in forming cylindrical cups by the new die set of sheet
hydroforming process. The process parameters evaluated in this
research are polyurethane hardness, polyurethane thickness, forming
pressure path and polyurethane hole diameter. The design of
experiments based upon L9 orthogonal arrays by Taguchi was used
and analysis of variance (ANOVA) was employed to analyze the
effect of these parameters on the forming pressure. The analysis of
the results showed that the optimal combination for low forming
pressure is harder polyurethane, bigger diameter of polyurethane hole
and thinner polyurethane. Finally, the confirmation test was derived
based on the optimal combination of parameters and it was shown
that the Taguchi method is suitable to examine the optimization
process.
Digital Article Identifier (DAI):
51
13086
Bridged Quantum Cellular Automata based on Si/SiO2 Superlattices
Abstract: The new architecture for quantum cellular
automata is offered. A QCA cell includes two layers nc-Si,
divided by a dielectric. Among themselves cells are connected
by the bridge from a conductive material. The comparison is
made between this and QCA, offered earlier by C. Lent's
group.
Digital Article Identifier (DAI):
50
13112
Application of Neural Network and Finite Element for Prediction the Limiting Drawing Ratio in Deep Drawing Process
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Digital Article Identifier (DAI):
49
4314
Influence of Taguchi Selected Parameters on Properties of CuO-ZrO2 Nanoparticles Produced via Sol-gel Method
Abstract: The present paper discusses the selection of process
parameters for obtaining optimal nanocrystallites size in the CuOZrO2
catalyst. There are some parameters changing the inorganic
structure which have an influence on the role of hydrolysis and
condensation reaction. A statistical design test method is
implemented in order to optimize the experimental conditions of
CuO-ZrO2 nanoparticles preparation. This method is applied for the
experiments and L16 orthogonal array standard. The crystallites size
is considered as an index. This index will be used for the analysis in
the condition where the parameters vary. The effect of pH, H2O/
precursor molar ratio (R), time and temperature of calcination,
chelating agent and alcohol volume are particularity investigated
among all other parameters. In accordance with the results of
Taguchi, it is found that temperature has the greatest impact on the
particle size. The pH and H2O/ precursor molar ratio have low
influences as compared with temperature. The alcohol volume as
well as the time has almost no effect as compared with all other
parameters. Temperature also has an influence on the morphology
and amorphous structure of zirconia. The optimal conditions are
determined by using Taguchi method. The nanocatalyst is studied by
DTA-TG, XRD, EDS, SEM and TEM. The results of this research
indicate that it is possible to vary the structure, morphology and
properties of the sol-gel by controlling the above-mentioned
parameters.
Digital Article Identifier (DAI):
48
8447
Software Process Improvement: A Organizational Change that Need to be Managed and Motivated
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Digital Article Identifier (DAI):
47
14235
Synthesis and Characterization of Plasma Polymerized Thin Films Deposited from Benzene and Hexamethyldisiloxane using (PECVD) Method
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Digital Article Identifier (DAI):
46
9057
Effects of Variations in Generator Inputs for Small Signal Stability Studies of a Three Machine Nine Bus Network
Abstract: Small signal stability causes small perturbations in the
generator that can cause instability in the power network. It is
generally known that small signal stability are directly related to the
generator and load properties. This paper examines the effects of
generator input variations on power system oscillations for a small
signal stability study. Eigenvaules and eigenvectors are used to
examine the stability of the power system. The dynamic power
system's mathematical model is constructed and thus calculated using
load flow and small signal stability toolbox on MATLAB. The power
system model is based on a 3-machine 9-bus system that was
modified to suit this study. In this paper, Participation Factors are a
means to gauge the effects of variation in generation with other
parameters on the network are also incorporated.
Digital Article Identifier (DAI):
45
5984
Deposition Rate and Energy Enhancements of TiN Thin-Film in a Magnetized Sheet Plasma Source
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Digital Article Identifier (DAI):
44
9341
Energy Systems and Crushing Behavior of Fiber Reinforced Composite Materials
Abstract: Effect of geometry on crushing behavior, energy absorption and failure mode of woven roving jute fiber/epoxy laminated composite tubes were experimentally studied. Investigations were carried out on three different geometrical types of composite tubes (circular, square and radial corrugated) subjected to axial compressive loading. It was observed in axial crushing study that the load bearing capability is significantly influenced by corrugation geometry. The influence of geometries of specimens was supported by the plotted load – displacement curves of the tests.
Digital Article Identifier (DAI):
43
5724
Prediction the Deformation in Upsetting Process by Neural Network and Finite Element
Abstract: In this paper back-propagation artificial neural network
(BPANN) is employed to predict the deformation of the upsetting
process. To prepare a training set for BPANN, some finite element
simulations were carried out. The input data for the artificial neural
network are a set of parameters generated randomly (aspect ratio d/h,
material properties, temperature and coefficient of friction). The
output data are the coefficient of polynomial that fitted on barreling
curves. Neural network was trained using barreling curves generated
by finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process
Digital Article Identifier (DAI):
42
7455
Assessing the Function of Light and Colorin Architectural View
Abstract: Light is one of the most important qualitative and
symbolic factors and has a special position in architecture and urban
development in regard to practical function. The main function of
light, either natural or artificial, is lighting up the environment and
the constructional forms which is called lighting. However, light is
used to redefine the urban spaces by architectural genius with regard
to three aesthetic, conceptual and symbolic factors. In architecture
and urban development, light has a function beyond lighting up the
environment, and the designers consider it as one of the basic
components. The present research aims at studying the function of
light and color in architectural view and their effects in buildings.
Digital Article Identifier (DAI):
41
2327
Wind Farm Modeling for Steady State and Dynamic Analysis
Abstract: This paper focuses on PSS/E modeling of wind farms
of Doubly-fed Induction Generator (DFIG) type and their impact on
issues of power system operation. Since Wind Turbine Generators
(WTG) don-t have the same characteristics as synchronous
generators, the appropriate modeling of wind farms is essential for
transmission system operators to analyze the best options of
transmission grid reinforcements as well as to evaluate the wind
power impact on reliability and security of supply. With the high
excepted penetration of wind power into the power system a
simultaneous loss of Wind Farm generation will put at risk power
system security and reliability. Therefore, the main wind grid code
requirements concern the fault ride through capability and frequency
operation range of wind turbines. In case of grid faults wind turbines
have to supply a definite reactive power depending on the
instantaneous voltage and to return quickly to normal operation.
Digital Article Identifier (DAI):
40
11863
Re-Design of Load Shedding Schemes of the Kosovo Power System
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Digital Article Identifier (DAI):
39
6320
A Review on Application of Chitosan as a Natural Antimicrobial
Abstract: In recent years application of natural antimicrobials
instead of conventional ones, due to their hazardous effects on health,
has got serious attentions. On the basis of the results of different
studies, chitosan, a natural bio-degradable and non-toxic
biopolysaccharide derived from chitin, has potential to be used as a
natural antimicrobial. Chitosan has exhibited high antimicrobial
activity against a wide variety of pathogenic and spoilage
microorganisms, including fungi, and Gram-positive and Gramnegative
bacteria. The antimicrobial action is influenced by intrinsic
factors such as the type of chitosan, the degree of chitosan
polymerization and extrinsic factors such as the microbial organism,
the environmental conditions and presence of the other components.
The use of chitosan in food systems should be based on sufficient
knowledge of the complex mechanisms of its antimicrobial mode of
action. In this article we review a number of studies on the
investigation of chitosan antimicrobial properties and application of
them in culture and food mediums.
Digital Article Identifier (DAI):
38
8153
Determination of Alkaline Protease Production In Serratia Marcescens Sp7 Using Agro Wastes As Substrate Medium, Optimization Of Production Parameters And Purification Of The Enzyme
Abstract: The enzyme alkaline protease production was determined under
solid state fermentation using the soil bacteria Serratia marcescens
sp7. The maximum production was obtained from wheat bran
medium than ground nut shell and chemically defined medium. The
physiological fermentation factors such as pH of the medium (pH 8),
Temperature (40oC) and incubation time (48 hrs) played a vital role
in alkaline protease production in all the above. 100Mm NaCl has
given better resolution during elution of the enzymes. The enzyme
production was found to be associated with growth of the bacterial
culture.
Digital Article Identifier (DAI):
37
12661
Patterned Growth of ZnO Nanowire Arrays on Zinc Foil by Thermal Oxidation
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Digital Article Identifier (DAI):
36
7556
Evaluation of Water Quality of the Beshar River
Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Digital Article Identifier (DAI):
35
14963
Antioxidant Components of Fumaria Species(Papaveraceae)
Abstract: The genus Fumaria L. (Papaveraceae) in Iran
comprises 8 species with a vast medicinal use in Asian folk
medicine. These herbs are considered to be useful in the
treatment of gastrointestinal disease and skin disorders.
Antioxidant activities of alkaloids and phenolic extracts of
these species had been studied previously. These species are:
F. officinalis, F. parviflora, F. asepala, F. densiflora, F.
schleicheri, F. vaillantii and F. indica. More than 50
populations of Fumaria species were sampled from nature. In
this study different fatty acids are extracted. Their picks were
recorded by GC technique. This species contain some kind of
fatty acids with antioxidant effects. A part of these lipids are
phospholipids. As these are unsaturated fatty acids they may
have industrial use as natural additive to cosmetics, dermal
and oral medicines. The presences of different materials are
discussed. Our studies for antioxidant effects of these
substances are continued.
Digital Article Identifier (DAI):
34
11689
The Optimal Placement of Capacitor in Order to Reduce Losses and the Profile of Distribution Network Voltage with GA, SA
Abstract: Most of the losses in a power system relate to
the distribution sector which always has been considered.
From the important factors which contribute to increase losses
in the distribution system is the existence of radioactive flows.
The most common way to compensate the radioactive power
in the system is the power to use parallel capacitors. In
addition to reducing the losses, the advantages of capacitor
placement are the reduction of the losses in the release peak of
network capacity and improving the voltage profile. The point
which should be considered in capacitor placement is the
optimal placement and specification of the amount of the
capacitor in order to maximize the advantages of capacitor
placement.
In this paper, a new technique has been offered for the
placement and the specification of the amount of the constant
capacitors in the radius distribution network on the basis of
Genetic Algorithm (GA). The existing optimal methods for
capacitor placement are mostly including those which reduce
the losses and voltage profile simultaneously. But the
retaliation cost and load changes have not been considered as
influential UN the target function .In this article, a holistic
approach has been considered for the optimal response to this
problem which includes all the parameters in the distribution
network: The price of the phase voltage and load changes. So,
a vast inquiry is required for all the possible responses. So, in
this article, we use Genetic Algorithm (GA) as the most
powerful method for optimal inquiry.
Digital Article Identifier (DAI):
33
5241
Study of Iranian Biospherical Reservation Areas for Medicinal Plants Diversity
Abstract: The study was carried out to gather and identify
medicinal plants their curative effects and the part of them which is
used from the reservation area of Miankaleh. The region under study
has an area of 68800 hectares situated 12 kilometers north of the city
of Behshahr and northwest of the city of Gorgan. Results obtained
showed that out of a total of 43 families, 125 genera, and 155 species
found in the region, 33 families, 52 genera and 61 species (39% of all
the species) belonged to medicinal plants, among which the class
Asteraceae with 6 species and the class Chenopodiaceae with 5
species had the most medicinal species. The most used parts of the
plants were the leaves with 31%, the whole plants with 19%, and the
roots with 15%.
Digital Article Identifier (DAI):
32
15290
Distributed Load Flow Analysis using Graph Theory
Abstract: In today scenario, to meet enhanced demand imposed
by domestic, commercial and industrial consumers, various
operational & control activities of Radial Distribution Network
(RDN) requires a focused attention. Irrespective of sub-domains
research aspects of RDN like network reconfiguration, reactive
power compensation and economic load scheduling etc, network
performance parameters are usually estimated by an iterative process
and is commonly known as load (power) flow algorithm. In this
paper, a simple mechanism is presented to implement the load flow
analysis (LFA) algorithm. The reported algorithm utilizes graph
theory principles and is tested on a 69- bus RDN.
Digital Article Identifier (DAI):
31
15201
Effect of Friction Stir Welding on Microstructural and Mechanical Properties of Copper Alloy
Abstract: This study demonstrates the feasibility of joining the commercial pure copper plates by friction stir welding (FSW). Microstructure, microhardness and tensile properties in terms of the joint efficiency were found 94.03 % compare to as receive base material (BM). The average hardness at the top was higher than bottom. Hardness of weld zone was higher than the base material. Different microstructure zones were revealed by optical microscopy and scanning electron microscopy. The stirred zone (SZ) exhibited primary two phases namely, recrystallized grains and fine precipitates in matrix of copper.
Digital Article Identifier (DAI):
30
10547
An Alternative Method for Generating Almost Infinite Sequence of Gaussian Variables
Abstract: Most of the well known methods for generating
Gaussian variables require at least one standard uniform distributed
value, for each Gaussian variable generated. The length of the
random number generator therefore, limits the number of
independent Gaussian distributed variables that can be generated
meanwhile the statistical solution of complex systems requires a
large number of random numbers for their statistical analysis. We
propose an alternative simple method of generating almost infinite
number of Gaussian distributed variables using a limited number of
standard uniform distributed random numbers.
Digital Article Identifier (DAI):
29
13551
In vitro Study of Antibacterial Activity of Cymbopogon citratus
Abstract: Alcohol and water extracts of Cymbopogon citratus
was investigated for anti-bacterial properties and phytochemical
constituents. The extract was screened against four gram-negative
bacteria Escherichia coli, Klebsiella pneumoniae, Pseudomonas
aeruginosa, Proteus vulgaris) and two grampositive bacteria Bacillus
subtilis and Staphylococcus aureus at four different concentrations
(1:1, 1:5, 1:10 and 1:20) using disc diffusion method. The antibacterial
examination was by disc diffusion techniques, while the
photochemical constituents were investigated using standard
chemical methods. Results showed that the extracts inhibited the
growth of standard and local strains of the organisms used. The
treatments were significantly different (P = 0.05). The minimum
inhibitory concentration of the extracts against the tested
microorganisms ranged between 150mg/ml and 50mg/ml. The
alcohol extracts were found to be generally more effective than the
water extract. The photochemical analysis revealed the presence of
alkaloids and phenol but absence of cardiac and cyanogenic
glycosides. The presence of alkaloid and phenols were inferred as
being responsible for the anti-bacterial properties of the extracts.
Digital Article Identifier (DAI):
28
7192
Correlations between Cleaning Frequency of Reservoir and Water Tower and Parameters of Water Quality
Abstract: This study was investigated on sampling and
analyzing water quality in water reservoir & water tower installed in
two kind of residential buildings and school facilities. Data of water
quality was collected for correlation analysis with frequency of
sanitization of water reservoir through questioning managers of
building about the inspection charts recorded on equipment for water
reservoir. Statistical software packages (SPSS) were applied to the
data of two groups (cleaning frequency and water quality) for
regression analysis to determine the optimal cleaning frequency of
sanitization. The correlation coefficient (R) in this paper represented
the degree of correlation, with values of R ranging from +1 to -1.After
investigating three categories of drinking water users; this study found
that the frequency of sanitization of water reservoir significantly
influenced the water quality of drinking water. A higher frequency of
sanitization (more than four times per 1 year) implied a higher quality
of drinking water. Results indicated that sanitizing water reservoir &
water tower should at least twice annually for achieving the aim of
safety of drinking water.
Digital Article Identifier (DAI):
27
6845
Performance Evaluation of TCP Vegas versus Different TCP Variants in Homogeneous and Heterogeneous Wired Networks
Abstract: A study on the performance of TCP Vegas versus
different TCP variants in homogeneous and heterogeneous wired
networks are performed via simulation experiment using network
simulator (ns-2). This performance evaluation prepared a comparison
medium for the performance evaluation of enhanced-TCP Vegas in
wired network and for wireless network. In homogeneous network,
the performance of TCP Tahoe, TCP Reno, TCP NewReno, TCP
Vegas and TCP SACK are analyzed. In heterogeneous network, the
performances of TCP Vegas against TCP variants are analyzed. TCP
Vegas outperforms other TCP variants in homogeneous wired
network. However, TCP Vegas achieves unfair throughput in
heterogeneous wired network.
Digital Article Identifier (DAI):
26
11068
Systematic Study of the p, d and 3He Elastic Scattering on 6Li
Abstract: the elastic scattering of protons, deuterons and 3He on 6Li at different incident energies have been analyzed in the framework of the optical model using ECIS88 as well as SPI GENOA codes. The potential parameters were extracted in the phenomenological treatment of measured by us angular distributions and literature data. A good agreement between theoretical and experimental differential cross sections was obtained in whole angular range. Parameters for real part of potential have been also calculated microscopically with singleand double-folding model for the p and d, 3He scattering, respectively, using DFPOT code. For best agreement with experiment the normalization factor N for the potential depth is obtained in the range of 0.7-0.9.
Digital Article Identifier (DAI):
25
2976
Fabrication of Carbon Doped TiO2 Nanotubes via In-situ Anodization of Ti-foil in Acidic Medium
Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.
Digital Article Identifier (DAI):
24
2367
Deep iCrawl: An Intelligent Vision-Based Deep Web Crawler
Abstract: The explosive growth of World Wide Web has posed
a challenging problem in extracting relevant data. Traditional web
crawlers focus only on the surface web while the deep web keeps
expanding behind the scene. Deep web pages are created
dynamically as a result of queries posed to specific web databases.
The structure of the deep web pages makes it impossible for
traditional web crawlers to access deep web contents. This paper,
Deep iCrawl, gives a novel and vision-based approach for extracting
data from the deep web. Deep iCrawl splits the process into two
phases. The first phase includes Query analysis and Query translation
and the second covers vision-based extraction of data from the
dynamically created deep web pages. There are several established
approaches for the extraction of deep web pages but the proposed
method aims at overcoming the inherent limitations of the former.
This paper also aims at comparing the data items and presenting them
in the required order.
Digital Article Identifier (DAI):
23
9570
UTHM Hand: Mechanics Behind The Dexterous Anthropomorphic Hand
Abstract: A multi fingered dexterous anthropomorphic hand is
being developed by the authors. The focus of the hand is the
replacement of human operators in hazardous environments and also
in environments where zero tolerance is observed for the human
errors. The robotic hand will comprise of five fingers (four fingers
and one thumb) each having four degrees of freedom (DOF) which
can perform flexion, extension, abduction, adduction and also
circumduction. For the actuation purpose pneumatic muscles and
springs will be used. The paper exemplifies the mechanical design for
the robotic hand. It also describes different mechanical designs that
have been developed before date.
Digital Article Identifier (DAI):
22
15689
An Assessment of Water Pollution of the Beshar River Aquatic Ecosystems
Abstract: The Beshar River is one of the most important aquatic ecosystems in the upstream of the Karun watershed in south of Iran which is affected by point and non point pollutant sources . This study was done in order to evaluate the effects of pollutants activities on the water quality of the Beshar river and its aquatic ecosystems. This river is approximately 190 km in length and situated at the geographical positions of 51° 20´ to 51° 48´ E and 30° 18´ to 30° 52´ N it is one of the most important aquatic ecosystems of Kohkiloye and Boyerahmad province in south-west Iran. In this research project, five study stations were selected to examine water pollution in the Beshar River systems. Human activity is now one of the most important factors affecting on hydrology and water quality of the Beshar river. Humans use large amounts of resources to sustain various standards of living, although measures of sustainability are highly variable depending on how sustainability is defined. The Beshar river ecosystems are particularly sensitive and vulnerable to human activities. Therefore, to determine the impact of human activities on the Beshar River, the most important water quality parameters such as pH, dissolve oxygen (DO), Biological Oxygen Demand (BOD5), Total Dissolve Solids (TDS), Nitrates (NO3-N) and Phosphates (PO4) were estimated at the five stations. As the results show, the most important pollution index parameters such as BOD5, NO3 and PO4 increase and DO and pH decrease according to human activities (P<0.05). However, due to pollutant degradation and dilution, pollution index parameters improve downstream sampling stations.
Digital Article Identifier (DAI):
21
560
Anticancer Effect of Doxorubicin Loaded Heparin based Super-paramagnetic Iron oxide Nanoparticles against the Human Ovarian Cancer Cells
Abstract: This study determines the effect of naked and heparinbased
super-paramagnetic iron oxide nanoparticles on the human
cancer cell lines of A2780. Doxorubicin was used as the anticancer
drug, entrapped in the SPIO-NPs. This study aimed to decorate
nanoparticles with heparin, a molecular ligand for 'active' targeting
of cancerous cells and the application of modified-nanoparticles in
cancer treatment. The nanoparticles containing the anticancer drug
DOX were prepared by a solvent evaporation and emulsification
cross-linking method. The physicochemical properties of the
nanoparticles were characterized by various techniques, and uniform
nanoparticles with an average particle size of 110±15 nm with high
encapsulation efficiencies (EE) were obtained. Additionally, a
sustained release of DOX from the SPIO-NPs was successful.
Cytotoxicity tests showed that the SPIO-DOX-HP had higher cell
toxicity than the individual HP and confocal microscopy analysis
confirmed excellent cellular uptake efficiency. These results indicate
that HP based SPIO-NPs have potential uses as anticancer drug
carriers and also have an enhanced anticancer effect.
Digital Article Identifier (DAI):
20
3947
Natural Radioactivity Measurements of Basalt Rocks in Sidakan District Northeastern of Kurdistan Region-Iraq
Abstract: The amounts of radioactivity in the igneous rocks
have been investigated; samples were collected from the total of eight
basalt rock types in the northeastern of Kurdistan region/Iraq. The
activity concentration of 226Ra (238U) series, 228Ac (232Th) series, 40K
and 137Cs were measured using Planar HPGe and NaI(Tl) detectors.
Along the study area the radium equivalent activities Raeq in Bq/Kg
of samples under investigation were found in the range of 22.16 to
77.31 Bq/Kg with an average value of 44.8 Bq/Kg, this value is much
below the internationally accepted value of 370 Bq/Kg. To estimate
the health effects of this natural radioactive composition, the average
values of absorbed gamma dose rate D (55 nGyh-1), Indoor and
outdoor annual effective dose rates Eied (0.11 mSvy-1) . and Eoed
(0.03 mSvy-1), External hazard index Hex (0.138) and internal hazard
index Hin(0.154), and representative level index Iγr (0.386) have been
calculated and found to be lower than the worldwide average values.
Digital Article Identifier (DAI):
19
6441
Development and Characterization of Normoxic Polyhydroxyethylacrylate (PHEA) Gel Dosimeter using Raman Spectroscopy
Abstract: Raman spectroscopy are used to characterize the
chemical changes in normoxic polyhydroxyethylacrylate gel
dosimeter (PHEA) induced by radiation. Irradiations in the low dose
region are performed and the polymerizations of PHEA gels are
monitored by the observing the changes of Raman shift intensity of
the carbon covalent bond of PHEA originated from both monomer
and the cross-linker. The variation in peak intensities with absorbed
dose was observed. As the dose increase, the peak intensities of
covalent bond of carbon in the polymer gels decrease. This point out
that the amount of absorbed dose affect the polymerization of
polymer gels. As the absorbed dose increase, the polymerizations
also increase. Results verify that PHEA gel dosimeters are sensitive
even in lower dose region.
Digital Article Identifier (DAI):
18
2616
Association of the p53 Codon 72 Polymorphism with Colorectal Cancer in South West of Iran
Abstract: The p53 tumor suppressor gene plays two important
roles in genomic stability: blocking cell proliferation after DNA
damage until it has been repaired, and starting apoptosis if the
damage is too critical. Codon 72 exon4 polymorphism (Arg72Pro) of
the P53 gene has been implicated in cancer risk. Various studies have
been done to investigate the status of p53 at codon 72 for arginine
(Arg) and proline (Pro) alleles in different populations and also the
association of this codon 72 polymorphism with various tumors. Our
objective was to investigate the possible association between P53
Arg72Pro polymorphism and susceptibility to colorectal cancer
among Isfahan and Chaharmahal Va Bakhtiari (a part of south west
of Iran) population. We investigated the status of p53 at codon 72 for
Arg/Arg, Arg/Pro and Pro/Pro allele polymorphisms in blood
samples from 145 colorectal cancer patients and 140 controls by
Nested-PCR of p53 exon 4 and digestion with BstUI restriction
enzyme and the DNA fragments were then resolved by
electrophoresis in 2% agarose gel. The Pro allele was 279 bp, while
the Arg allele was restricted into two fragments of 160 and 119 bp.
Among the 145 colorectal cancer cases 49 cases (33.79%) were
homozygous for the Arg72 allele (Arg/Arg), 18 cases (12.41%) were
homozygous for the Pro72 allele (Pro/Pro) and 78 cases (53.8%)
found in heterozygous (Arg/Pro).
In conclusion, it can be said that p53Arg/Arg genotype may be
correlated with possible increased risk of this kind of cancers in south
west of Iran.
Digital Article Identifier (DAI):
17
15761
Vibration of Functionally Graded Cylindrical Shells under Free-Free Boundary Conditions
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free boundary conditions.
Digital Article Identifier (DAI):
16
11284
Aligning IS Development with Users- Work Habits
Abstract: As a primitive assumption, if a new information
system is able to remind users their old work habits, it should have a
better opportunity to be accepted, adopted and finally, utilized. In
this paper some theoretical concepts borrowed from psychodynamic
theory e.g. ego defenses are discussed to show how such resemblance
can be made without necessarily affecting the performance of the
new system. The main assertion is a new system should somehow
imitate old work habits, not literally, but through following their
paces in terms of the order of habitual tensional states including
stimulation, defensive actions and satisfactions.
Digital Article Identifier (DAI):
15
1039
Silicon Application and Nitrogen on Yield and Yield Components in Rice (Oryza sativa L.) in Two Irrigation Systems
Abstract: Silicon is a beneficial element for plant growth. It
helps plants to overcome multiple stresses, alleviates metal toxicity
and improves nutrient imbalance. Field experiment was conducted as
split-split plot arranged in a randomized complete block design with
four replications. Irrigation system include continues flooding and
deficit as main plots and nitrogen rates N0, N46, N92, and N138 kg/ha
as sub plots and silicon rates Si0 & Si500 kg/ha as sub-subplots.
Results indicate that grain yield had not significant difference
between irrigation systems. Flooding irrigation had higher biological
yield than deficit irrigation whereas, no significant difference in grain
and straw yield. Nitrogen application increased grain, biological and
straw yield. Silicon application increased grain, biological and straw
yield but, decreased harvest index. Flooding irrigation had higher
number of total tillers / hill than deficit irrigation, but deficit
irrigation had higher number of fertile tillers / hill than flooding
irrigation. Silicon increased number of filled spikelet and decreased
blank spikelet. With high nitrogen application decreased 1000-grain
weight. It can be concluded that if the nitrogen application was high
and water supplied was available we could have silicon application
until increase grain yield.
Digital Article Identifier (DAI):
14
1517
The First Prevalence Report of Direct Identification and Differentiation of B. abortus and B. melitensis using Real Time PCR in House Mouse of Iran
Abstract: Brucellosis is a zoonotic disease; its symptoms and appearances are not exclusive in human and its traditional diagnosis is based on culture, serological methods and conventional PCR. For more sensitive, specific detection and differentiation of Brucella spp., the real time PCR method is recommended. This research has performed to determine the presence and prevalence of Brucella spp. and differentiation of Brucella abortus and Brucella melitensis in house mouse (Mus musculus) in west of Iran. A TaqMan analysis and single-step PCR was carried out in total 326 DNA of Mouse's spleen samples. From the total number of 326 samples, 128 (39.27%) gave positive results for Brucella spp. by conventional PCR, also 65 and 32 out of the 128 specimens were positive for B. melitensis, B. abortus, respectively. These results indicate a high presence of this pathogen in this area and that real time PCR is considerably faster than current standard methods for identification and differentiation of Brucella species. To our knowledge, this study is the first prevalence report of direct identification and differentiation of B. abortus and B. melitensis by real time PCR in mouse tissue samples in Iran.
Digital Article Identifier (DAI):
13
11550
Hexavalent Chromium Removal from Aqueous Solutions by Adsorption onto Synthetic Nano Size ZeroValent Iron (nZVI)
Abstract: The present work was conducted for the synthesis of
nano size zerovalent iron (nZVI) and hexavalent chromium (Cr(VI))
removal as a highly toxic pollutant by using this nanoparticles. Batch
experiments were performed to investigate the effects of Cr(VI),
nZVI concentration, pH of solution and contact time variation on
the removal efficiency of Cr(VI). nZVI was synthesized by
reduction of ferric chloride using sodium borohydrid. SEM and
XRD examinations applied for determination of particle size and
characterization of produced nanoparticles. The results showed that
the removal efficiency decreased with Cr(VI) concentration and pH
of solution and increased with adsorbent dosage and contact time.
The Langmuir and Freundlich isotherm models were used for the
adsorption equilibrium data and the Langmuir isotherm model was
well fitted. Nanoparticle ZVI presented an outstanding ability to
remove Cr(VI) due to high surface area, low particle size and high
inherent activity.
Digital Article Identifier (DAI):
12
2567
Economic Dispatch Fuzzy Linear Regression and Optimization
Abstract: This study presents a new approach based on Tanaka's
fuzzy linear regression (FLP) algorithm to solve well-known power
system economic load dispatch problem (ELD). Tanaka's fuzzy linear
regression (FLP) formulation will be employed to compute the
optimal solution of optimization problem after linearization. The
unknowns are expressed as fuzzy numbers with a triangular
membership function that has middle and spread value reflected on
the unknowns. The proposed fuzzy model is formulated as a linear
optimization problem, where the objective is to minimize the sum of
the spread of the unknowns, subject to double inequality constraints.
Linear programming technique is employed to obtain the middle and
the symmetric spread for every unknown (power generation level).
Simulation results of the proposed approach will be compared with
those reported in literature.
Digital Article Identifier (DAI):
11
1746
Non-Sensitive Solutions in Multi-Objective Optimization of a Solar Photovoltaic/Thermal(PV/T) Air Collector
Abstract: In this paper, an attempt has been made to obtain nonsensitive
solutions in the multi-objective optimization of a
photovoltaic/thermal (PV/T) air collector. The selected objective
functions are overall energy efficiency and exergy efficiency.
Improved thermal, electrical and exergy models are used to calculate
the thermal and electrical parameters, overall energy efficiency,
exergy components and exergy efficiency of a typical PV/T air
collector. A computer simulation program is also developed. The
results of numerical simulation are in good agreement with the
experimental measurements noted in the previous literature. Finally,
multi-objective optimization has been carried out under given
climatic, operating and design parameters. The optimized ranges of
inlet air velocity, duct depth and the objective functions in optimal
Pareto front have been obtained. Furthermore, non-sensitive solutions
from energy or exergy point of view in the results of multi-objective
optimization have been shown.
Digital Article Identifier (DAI):
10
425
Dynamic Response of Strain Rate Dependent Glass/Epoxy Composite Beams Using Finite Difference Method
Abstract: This paper deals with a numerical analysis of the
transient response of composite beams with strain rate dependent
mechanical properties by use of a finite difference method. The
equations of motion based on Timoshenko beam theory are derived.
The geometric nonlinearity effects are taken into account with von
Kármán large deflection theory. The finite difference method in
conjunction with Newmark average acceleration method is applied to
solve the differential equations. A modified progressive damage
model which accounts for strain rate effects is developed based on
the material property degradation rules and modified Hashin-type
failure criteria and added to the finite difference model. The
components of the model are implemented into a computer code in
Mathematica 6. Glass/epoxy laminated composite beams with
constant and strain rate dependent mechanical properties under
dynamic load are analyzed. Effects of strain rate on dynamic
response of the beam for various stacking sequences, load and
boundary conditions are investigated.
Digital Article Identifier (DAI):
9
14506
Planar Tracking Control of an Underactuated Autonomous Underwater Vehicle
Abstract: This paper addresses the problem of trajectory
tracking control of an underactuated autonomous underwater vehicle
(AUV) in the horizontal plane. The underwater vehicle under
consideration is not actuated in the sway direction, and the system
matrices are not assumed to be diagonal and linear, as often found in
the literature. In addition, the effect of constant bias of environmental
disturbances is considered. Using backstepping techniques and the
tracking error dynamics, the system states are stabilized by forcing
the tracking errors to an arbitrarily small neighborhood of zero. The
effectiveness of the proposed control method is demonstrated through
numerical simulations. Simulations are carried out for an
experimental vehicle for smooth, inertial, two dimensional (2D)
reference trajectories such as constant velocity trajectory (a circle
maneuver – constant yaw rate), and time varying velocity trajectory
(a sinusoidal path – sinusoidal yaw rate).
Digital Article Identifier (DAI):
8
10930
Prediction of Overall Efficiency in Multistage Gear Trains
Abstract: A mathematical model for determining the overall efficiency
of a multistage tractor gearbox including all gear, lubricant,
surface finish related parameters and operating conditions is
presented. Sliding friction, rolling friction and windage losses were
considered as the main sources of power loss in the gearing system. A
computer code in FORTRAN was developed to simulate the model.
Sliding friction contributes about 98% of the total power loss for
gear trains operating at relatively low speeds (less than 2000 rpm
input speed). Rolling frictional losses decrease with increased load
while windage losses are only significant for gears running at very
high speeds (greater than 3000 rpm). The results also showed that the
overall efficiency varies over the path of contact of the gear meshes
ranging between 94% to 99.5%.
Digital Article Identifier (DAI):
7
3553
Comparison of Three Turbulence Models in Wear Prediction of Multi-Size Particulate Flow through Rotating Channel
Abstract: The present work compares the performance of three
turbulence modeling approach (based on the two-equation k -ε
model) in predicting erosive wear in multi-size dense slurry flow
through rotating channel. All three turbulence models include
rotation modification to the production term in the turbulent kineticenergy
equation. The two-phase flow field obtained numerically
using Galerkin finite element methodology relates the local flow
velocity and concentration to the wear rate via a suitable wear model.
The wear models for both sliding wear and impact wear mechanisms
account for the particle size dependence. Results of predicted wear
rates using the three turbulence models are compared for a large
number of cases spanning such operating parameters as rotation rate,
solids concentration, flow rate, particle size distribution and so forth.
The root-mean-square error between FE-generated data and the
correlation between maximum wear rate and the operating
parameters is found less than 2.5% for all the three models.
Digital Article Identifier (DAI):
6
13901
Bond Graph Modeling of Inter-Actuator Interactions in a Multi-Cylinder Hydraulic System
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Digital Article Identifier (DAI):
5
10197
Some Mechanical Properties of Cement Stabilized Malaysian Soft Clay
Abstract: Soft clays are defined as cohesive soil whose water
content is higher than its liquid limits. Thus, soil-cement mixing is
adopted to improve the ground conditions by enhancing the strength
and deformation characteristics of the soft clays. For the above
mentioned reasons, a series of laboratory tests were carried out to
study some fundamental mechanical properties of cement stabilized
soft clay. The test specimens were prepared by varying the portion of
ordinary Portland cement to the soft clay sample retrieved from the
test site of RECESS (Research Centre for Soft Soil). Comparisons
were made for both homogeneous and columnar system specimens
by relating the effects of cement stabilized clay of for 0, 5 and 10 %
cement and curing for 3, 28 and 56 days. The mechanical properties
examined included one-dimensional compressibility and undrained
shear strength. For the mechanical properties, both homogeneous and
columnar system specimens were prepared to examine the effect of
different cement contents and curing periods on the stabilized soil.
The one-dimensional compressibility test was conducted using an
oedometer, while a direct shear box was used for measuring the
undrained shear strength. The higher the value of cement content, the
greater is the enhancement of the yield stress and the decrease of
compression index. The value of cement content in a specimen is a
more active parameter than the curing period.
Digital Article Identifier (DAI):
4
7130
A Novel Approach of Route Choice in Stochastic Time-varying Networks
Abstract: Many exist studies always use Markov decision
processes (MDPs) in modeling optimal route choice in
stochastic, time-varying networks. However, taking many
variable traffic data and transforming them into optimal route
decision is a computational challenge by employing MDPs in
real transportation networks. In this paper we model finite
horizon MDPs using directed hypergraphs. It is shown that the
problem of route choice in stochastic, time-varying networks
can be formulated as a minimum cost hyperpath problem, and
it also can be solved in linear time. We finally demonstrate the
significant computational advantages of the introduced
methods.
Digital Article Identifier (DAI):
3
10734
Tropical Peat Soil Stabilization using Class F Pond Ash from Coal Fired Power Plant
Abstract: This paper presents the stabilization potential of Class
F pond ash (PA) from a coal fired thermal power station on tropical
peat soil. Peat or highly organic soils are well known for their high
compressibility, natural moisture content, low shear strength and
long-term settlement. This study investigates the effect of different
amount (i.e., 5, 10, 15 and 20%) of PA on peat soil, collected from
Sarawak, Malaysia, mainly compaction and unconfined compressive
strength (UCS) properties. The amounts of PA added to the peat soil
sample as percentage of the dry peat soil mass. With the increase in
PA content, the maximum dry density (MDD) of peat soil increases,
while the optimum moisture content (OMC) decreases. The UCS
value of the peat soils increases significantly with the increase of PA
content and also with curing periods. This improvement on
compressive strength of tropical peat soils indicates that PA has the
potential to be used as a stabilizer for tropical peat soil. Also, the use
of PA in soil stabilization helps in reducing the pond volume and
achieving environment friendly as well as a sustainable development
of natural resources.
Digital Article Identifier (DAI):
2
3527
Compressive Strength and Workability Characteristics of Low-Calcium Fly ash-based Self-Compacting Geopolymer Concrete
Abstract: Due to growing environmental concerns of the cement
industry, alternative cement technologies have become an area of
increasing interest. It is now believed that new binders are
indispensable for enhanced environmental and durability
performance. Self-compacting Geopolymer concrete is an innovative
method and improved way of concreting operation that does not
require vibration for placing it and is produced by complete
elimination of ordinary Portland cement.
This paper documents the assessment of the compressive strength
and workability characteristics of low-calcium fly ash based selfcompacting
geopolymer concrete. The essential workability
properties of the freshly prepared Self-compacting Geopolymer
concrete such as filling ability, passing ability and segregation
resistance were evaluated by using Slump flow, V-funnel, L-box and
J-ring test methods. The fundamental requirements of high
flowability and segregation resistance as specified by guidelines on
Self Compacting Concrete by EFNARC were satisfied. In addition,
compressive strength was determined and the test results are included
here. This paper also reports the effect of extra water, curing time and
curing temperature on the compressive strength of self-compacting
geopolymer concrete. The test results show that extra water in the
concrete mix plays a significant role. Also, longer curing time and
curing the concrete specimens at higher temperatures will result in
higher compressive strength.
Digital Article Identifier (DAI):
1
11640
Design of Stilling Basins using Artificial Roughness
Abstract: The stilling basins are commonly used to dissipate the
energy and protect the downstream floor from erosion. The aim of
the present experimental work is to improve the roughened stilling
basin using T-shape roughness instead of the regular cubic one and
design this new shape. As a result of the present work the best
intensity and the best roughness length are identified. Also, it is
found that the T-shape roughness save materials and reduce the jump
length compared to the cubic one. Sensitivity analysis was performed
and it was noticed that the change in the length of jump is more
sensitive to the change in roughness length than the change in
intensity.
Digital Article Identifier (DAI):